 Gauging interest...pun intended, Semi-custom wired Wide Band O2 meter, AFR |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mark Henry |
 Apr 21 2019, 09:03 AM
Post
#1
|
|
that's what I do!  Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada  |
I'm making up several 14point7 SLC free 2, WB O2 meters for customers and myself and just wondering if this would be of interest to the brotherhood.
Problem with most O2 meters is the wire harness, most of the time they are just a bit short for a clean rear/mid engine install. The wires are often cheaper quality loose wire covered with the Chinese finger puzzle like plastic sheathing. I'm using a high quality sheath, twisted, 6 wire with shrink wrap tubing on the ends, for the main harness. Attached image(s) 
|
   |
 
|
  |
Replies
| mb911 |
Apr 21 2019, 01:41 PM
Post
#2
|
|
914 Guru Group: Members Posts: 7,560 Joined: 2-January 09 From: Burlington wi Member No.: 9,892 Region Association: Upper MidWest 
|
Mark,
I think I would be in.. I need something and currently have nothing so this would help. |
|
|
|
| Mark Henry |
Apr 21 2019, 02:20 PM
Post
#3
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
QUOTE(mb911 @ Apr 21 2019, 03:41 PM)  Mark, I think I would be in.. I need something and currently have nothing so this would help. Ben we'll talk, you may already offer this as an option, but I'd like you to offer the bungs welded in on you're headers/exchangers. I have MSDS headers but the placement just pass the collector should be the similar. The tangerine /4 header I have here has a bung welded in I'll have to mock up a /4 to see the location. I want, not only for myself, but to have the perfect locations for peeps to mount the lambda on their exhaust. My headers are ceramic coated how far do I have to grind the coating back to weld my bungs in? I want to do as little as required. 1/4 inch? |
|
|
|
Posts in this topic
Mark Henry Gauging interest...pun intended Apr 21 2019, 09:03 AM
Mark Henry The meter works with any fuel, gas, diesel, alcoho... Apr 21 2019, 09:08 AM mobymutt I have interest, although I've pretty much blo... Apr 21 2019, 09:21 AM Mark Henry As I said these come as a kit, I have to solder in... Apr 21 2019, 09:23 AM mepstein I'll take one. Tell me when you want money. Th... Apr 21 2019, 09:30 AM
Mark Henry
I'll take one. Tell me when you want money. T... Apr 21 2019, 09:39 AM Mark Henry This shows the solder job on the daughter board, I... Apr 21 2019, 09:45 AM Mark Henry The 4.9 LSU connector, 2nd pic black doesn't s... Apr 21 2019, 09:56 AM Mark Henry This is the power and output leads, fuse and holde... Apr 21 2019, 10:06 AM jd74914 How much? Is that a 14point7 SLC board? Apr 21 2019, 10:26 AM Mark Henry
How much? Is that a 14point7 SLC board?
Yes it... Apr 21 2019, 12:10 PM jd74914
Yes it's a 14point7 (.com) I thought I said t... Apr 22 2019, 10:27 AM Mark Henry I likely could make each one around $10 cheap... Apr 21 2019, 12:42 PM ctc911ctc Ready to ship yet?
I likely could make each ... May 15 2019, 11:20 AM mb911 Mark ,
1/4" should be perfect. I just did t... Apr 21 2019, 07:28 PM Mark Henry
Mark ,
1/4" should be perfect. I just did ... Apr 22 2019, 05:17 AM tmessenger I bought one of these for my car a couple of month... Apr 21 2019, 08:03 PM mb911 Mark,
I had always read 10 to 2 o clock? Apr 22 2019, 05:35 AM Mark Henry
Mark,
I had always read 10 to 2 o clock?
10 or ... Apr 22 2019, 11:09 AM 914forme Dual setup would be my choice if your counting Mar... Apr 22 2019, 07:53 AM mepstein :) Apr 22 2019, 11:17 AM mb911 I was just looking at innovates website after I wr... Apr 22 2019, 11:32 AM Mark Henry Maybe I'm wrong or misinformed, wouldn't b... Apr 22 2019, 12:41 PM mb911
Maybe I'm wrong or misinformed, wouldn't ... Apr 22 2019, 02:52 PM Gary Mark, I'm in for a setup too, probably a two-h... Apr 22 2019, 05:59 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 03:21 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.