 More Novice Help Please, Suspension, CV Joint and Front Suspension Disassembly |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Highland |
 May 13 2019, 03:20 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 542 Joined: 8-August 11 From: San Diego, CA Member No.: 13,418 Region Association: Southern California  |
More amateur help please, this time with CV joint and front suspension:
1) I've only taken apart one axle, but I found some pitting on one of the outside bearing. Pictured is the worse example:   Can I address this by swapping the transmission end for the wheel end? I notice they ride in slightly different locations. 2) Having much trouble taking apart the front suspension. a) Can I just use a fork to pry this off or do I need a puller/pusher device? I have neither so trying to avoid buying both. Soaking in PB Blaster now. Boot is already torn so a fork would do no damage, just looking for the easiest way.  b) According to the Haines Manual the bolt/pin shown is suppose to come out to release the ball joint (held in by a semi-circle feature?). Mine looks like it is permanently attached to the strut. How do I get it out?   3) When removing the control arms do the adjusters need to be wound loose? Can the cross support bar be left in place? |
   |
 
|
  |
Replies
| rhodyguy |
May 16 2019, 08:02 PM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,240 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
Spray down the thread end. Smack the othe side, while wet, with a large drift. It will help with breaking the rust bond inside the bolt hole. A pointed bit in an air chisel works well for getting the balljoint out of the arm. There's a dimple in the top. Aerokroil is a good penetrant also.
|
|
|
|
Posts in this topic
Highland More Novice Help Please, Suspension May 13 2019, 03:20 PM
76-914 Yes you can use a fork. Put the nut back on the bo... May 13 2019, 03:34 PM
KELTY360
Yes you can use a fork. Put the nut back on the b... May 15 2019, 10:23 PM Superhawk996 1) You can but it is only a temporary solution at... May 13 2019, 03:39 PM jtprettyman For item #2, I'll second Superhawk - use a tie... May 14 2019, 03:45 PM Highland Thanks.
2a) Followed your advice and went to Auto... May 14 2019, 04:19 PM porschetub I hate the fork tool as they tend to destroy the r... May 14 2019, 04:23 PM Highland What is the proper tool for removing the pin attac... May 14 2019, 08:25 PM Luke M
What is the proper tool for removing the pin atta... May 15 2019, 01:39 PM Superhawk996
What is the proper tool for removing the pin att... May 15 2019, 06:34 PM 76-914
What is the proper tool for removing the pin att... May 16 2019, 08:33 AM 914Toy
What is the proper tool for removing the pin atta... May 15 2019, 02:07 PM mepstein I bought a pair of 911 struts super cheap because ... May 15 2019, 06:57 PM Superhawk996
I bought a pair of 911 struts super cheap because... May 15 2019, 07:33 PM mepstein
I bought a pair of 911 struts super cheap becaus... May 15 2019, 07:38 PM malcolm2 Tangerine Racing has CV joints. If 3 of yours are... May 15 2019, 07:32 PM Highland More heat and I got the ball joint pins out. Kind ... May 16 2019, 07:10 PM Superhawk996 Nice job. You’re on your way!
:beer2: May 16 2019, 07:20 PM mepstein Usually, you only need to replace torsion bars if ... May 16 2019, 07:35 PM bbrock
Tangerine Racing has CV joints. If 3 of yours ar... May 16 2019, 07:47 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 04:22 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.