 Identify Cam Without Splitting Cases, 2.0 Liter 4 |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| motorvated |
 Jul 9 2018, 08:51 AM
Post
#1
|
|
Member  Group: Members Posts: 281 Joined: 13-February 13 From: Colorado Member No.: 15,519 Region Association: Rocky Mountains  |
Is it possible to determine what cam is inside the 2.0 liter four cylinder motor I just purchased, without splitting the cases. Can a dial gauge on the rocker arms and degree wheel on the flywheel be used to measure the cam lift and profile. Are any cam markings visible without splitting the cases. The engine was last run with carbs, but no history of whether or not the cam was ever changed. I'd prefer not to disturb the bottom end if possible. Tried a search, but couldn't find anything.
|
   |
 
|
  |
Replies
| Dave_Darling |
Jul 9 2018, 04:58 PM
Post
#2
|
|
914 Idiot Group: Members Posts: 14,991 Joined: 9-January 03 From: Silicon Valley / Kailua-Kona Member No.: 121 Region Association: Northern California 
|
And of course you can put a dial indicator on a pushrod or a lifter (if you can get access) or a rocker arm and use a degree wheel on the crank. It can be tough to match those measurements up with published info, though.
--DD |
|
|
|
| motorvated |
Aug 24 2019, 12:21 PM
Post
#3
|
|
Member Group: Members Posts: 281 Joined: 13-February 13 From: Colorado Member No.: 15,519 Region Association: Rocky Mountains |
QUOTE(Dave_Darling @ Jul 9 2018, 04:58 PM)  And of course you can put a dial indicator on a pushrod or a lifter (if you can get access) or a rocker arm and use a degree wheel on the crank. It can be tough to match those measurements up with published info, though. --DD Updating an older thread. Just pulled the oil pump off of the 2.0 liter motor to see what cam might be in it. Here's what I found.  Looks like the oil pump drive is riveted on and not bolted, so am I correct to assume that the cam is most likely the original D-Jet fuel injection cam. Since the motor came to me with a set of 40IDF Webers, which I would like to use on this motor, is it time to split the cases and drop in a more carb friendly cam. Or can I run the carbs with this cam without leaving too much performance on the table. I also could swap over the L-Jet that currently is on the 1.8 Liter motor that currently is in the car, if the cam is compatible with that. Or I guess I could source a D-Jet set-up and bolt that on. I have been racing with various vintage clubs and SCCA with the 1.8, and would like to move up in the field a little with more power while staying at or below the 2.0 liter displacement limit that some clubs have. And I'm not looking for a killer race motor, just about 20 more hp than I have now. I'm apprehensive about splitting the cases, and maybe I shouldn't be. Any and all recommendations for a path forward with this motor will be appreciated greatly. |
|
|
|
Posts in this topic
motorvated Identify Cam Without Splitting Cases Jul 9 2018, 08:51 AM
injunmort I have been told the easiest way is to remove oil ... Jul 9 2018, 09:24 AM The Cabinetmaker Exactly like Mort said Jul 9 2018, 11:04 AM Mark Henry If it's bolted (aftermarket) most cam grinders... Jul 9 2018, 11:33 AM
JFJ914
[quote name='Dave_Darling' post='2627592' date='J... Aug 24 2019, 12:51 PM motorvated
[quote name='Dave_Darling' post='2627592' date='... Aug 24 2019, 01:06 PM Superhawk996 Nope. 2.0L (stock) is more like 95HP. But a 10H... Aug 24 2019, 05:03 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th June 2024 - 09:30 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.