 Strip this to bare metal and start again? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Tdskip |
 Jan 13 2020, 01:02 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 3,737 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None 
 |
I’ve shared some pictures here before but want to get going on this area repair and was hoping for some been there / repaired that.
I have Maddog’s patch panels in hand. Start by stripping to bare metal in this area? Thanks and hope everyone had a good weekend.  |
   |
 
|
  |
Replies
| rjames |
Jan 13 2020, 01:17 PM
Post
#2
|
|
I'm made of metal Group: Members Posts: 4,320 Joined: 24-July 05 From: Shoreline, WA Member No.: 4,467 Region Association: Pacific Northwest
|
Yup, it’s the only way to see what shape the metal is in around the rust holes. Looks like the PO did tried to repair it, but they must not have prepped the area properly given the rust holes around where the welding was done.
|
 |
|
| Tdskip |
Jan 13 2020, 02:03 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,737 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None
|
QUOTE(rjames @ Jan 13 2020, 02:17 PM)  Yup, it’s the only way to see what shape the metal is in around the rust holes. Looks like the PO did tried to repair it, but they must not have prepped the area properly given the rust holes around where the welding was done. Out the angle grinder comes...thanks mate. |
|
|
|
Posts in this topic
Tdskip Strip this to bare metal and start again? Jan 13 2020, 01:02 PM
Tdskip RE: Strip this to bare metal and start again? Jan 13 2020, 01:03 PM TargaToy I do not wish ill on anyone, nor do I want to impl... Jan 13 2020, 02:39 PM bretth It looks like it is only tack welded in. Worried a... Jan 13 2020, 03:02 PM
jimkelly i was thinking the same thing?
It looks like it ... Jan 13 2020, 07:00 PM Tdskip Thanks for the responses and considerations, this ... Jan 13 2020, 08:46 PM cary I think what you'll find is they laid new meta... Jan 13 2020, 09:37 PM aggiezig Like cary said, start peeling back the onion layer... Jan 13 2020, 11:27 PM Tdskip Thanks gentlemen, will try to dig in tonight.
Fin... Jan 14 2020, 12:06 PM Tdskip Underside looking up.
They patched right over old... Jan 14 2020, 03:07 PM SirAndy They patched right over old metal.
:sick: Jan 14 2020, 03:13 PM burton73 This is why we have to assume that most 914 for sa... Jan 14 2020, 03:14 PM TargaToy Looks like they patched right over the shelf attac... Jan 14 2020, 03:22 PM mtndawg I did a cut and replace that wasn’t too serious ... Jan 15 2020, 12:07 AM Uniquecoaches That is so sad that people do this. I have seen th... Jan 15 2020, 07:58 AM Tdskip @mtndawg - thanks for the link, very helpful. Ple... Jan 15 2020, 08:07 AM dr914@autoatlanta.com its ok for a patch job and you can grind the areas... Jan 15 2020, 08:56 AM Chi-town Cut it completely out. As you've shown there... Jan 15 2020, 10:17 AM 914werke :agree: Jan 15 2020, 12:18 PM Tdskip Thanks gentlemen, agree. I think I’m going to st... Jan 15 2020, 12:41 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 13th July 2025 - 05:26 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.