 Proper position of "cooling" flaps |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| SKL1 |
 May 18 2020, 08:50 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,831 Joined: 19-February 11 From: north Scottsdale Member No.: 12,732 Region Association: Upper MidWest 
 |
Surprised there is no good picture in the factory workshop manual to show position of the flaps in the closed or open positions.
In this picture it is in the fail-safe position as if the cable or thermostat wasn't working. Just want to make sure they are correct. When hooking up the thermostat wire the flaps would both move as the little "lever" would move down. Just seems strange that in the fail-safe mode it covers up the oil cooler- you 'd think it would want air going over and through the cooler to allow the engine to run cooler if the thermostat failed...  |
   |
 
|
  |
Replies
| barefoot |
May 19 2020, 04:54 AM
Post
#2
|
|
Senior Member Group: Members Posts: 1,571 Joined: 19-March 13 From: Charleston SC Member No.: 15,673 Region Association: South East States
|
This might help as well:
 |
|
|
|
| Craigers17 |
May 19 2020, 06:05 AM
Post
#3
|
|
Senior Member Group: Members Posts: 916 Joined: 5-August 17 From: Rome, GA Member No.: 21,317 Region Association: South East States
|
QUOTE(barefoot @ May 19 2020, 04:54 AM)  This might help as well: That's a very helpful drawing. Thanks! |
 |
|
Posts in this topic
SKL1 Proper position of "cooling" flaps May 18 2020, 08:50 PM
bbrock It's actually not covering up the oil cooler. ... May 18 2020, 08:54 PM cary https://bowlsby.net/914/Classic/zTN_Eng_Air..._Fla... May 18 2020, 08:56 PM SirAndy Just seems strange that in the fail-safe mode it c... May 18 2020, 09:13 PM SKL1 Thanks! I knew I had seen those somewhere bef... May 18 2020, 09:14 PM jim_hoyland How do you set the end of the wire in the clamp? E... May 18 2020, 09:32 PM
cuddy_k
How do you set the end of the wire in the clamp? ... May 18 2020, 09:43 PM
flipb
How do you set the end of the wire in the clamp? ... May 19 2020, 05:33 AM falcor75 Wire should be tight when the engine is cold since... May 18 2020, 09:44 PM Olympic 914
Wire should be tight when the engine is cold sinc... May 19 2020, 07:08 AM mtndawg http://www.914world.com/bbs2/index.php?sho...=9243... May 18 2020, 11:33 PM BeatNavy I find the easiest way is to carefully put a heat ... May 19 2020, 06:04 AM porschetub
I find the easiest way is to carefully put a heat... May 19 2020, 02:48 PM BeatNavy
Hot tip,replace the cable with a bike cable they ... May 19 2020, 02:58 PM andrewvolsen Edit: posted to wrong thread, sorry Nov 15 2026, 10:18 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 15th November 2026 - 02:50 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.