![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() |
windforfun |
![]()
Post
#1
|
Advanced Member ![]() ![]() ![]() ![]() Group: Members Posts: 2,057 Joined: 17-December 07 From: Blackhawk, CA Member No.: 8,476 Region Association: None ![]() ![]() |
Which FI system is best & why? I just watched George's video (most of it) & now I'm curious.
|
![]() ![]() |
JeffBowlsby |
![]()
Post
#2
|
914 Wiring Harnesses & Beekeeper ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 8,974 Joined: 7-January 03 From: San Ramon CA Member No.: 104 Region Association: None ![]() ![]() |
Word. Clipped rom Wikipedia:
The first commercial electronicially controlled manifold injection system was the Electrojector developed by Bendix and was offered by American Motors Corporation (AMC) in 1957.[34][35] Initial problems with the Electrojector meant only pre-production cars had it installed so very few cars were sold[36] and none were made available to the public.[37] The EFI system in the Rambler worked well in warm weather, but was difficult to start in cooler temperatures.[38] Chrysler offered Electrojector on the 1958 Chrysler 300D, DeSoto Adventurer, Dodge D-500, and Plymouth Fury, arguably the first series-production cars equipped with an EFI system.[39] The Electrojector patents were subsequently sold to Bosch, who developed the Electrojector into the Bosch D-Jetronic. The D in D-Jetronic stands for Druckfühlergesteuert, German for "pressure-sensor controlled"). The D-Jetronic was first used on the VW 1600TL/E in 1967. This was a speed/density system, using engine speed and intake manifold air density to calculate "air mass" flow rate and thus fuel requirements. Bosch superseded the D-Jetronic system with the K-Jetronic and L-Jetronic systems for 1974, though some cars (such as the Volvo 164) continued using D-Jetronic for the following several years. The L-Jetronic uses a mechanical airflow meter (L for Luft, German for "air") that produces a signal that is proportional to volume flow rate. This approach required additional sensors to measure the atmospheric pressure and temperature, to calculate mass flow rate. L-Jetronic was widely adopted on European cars of that period, and a few Japanese models a short time later. |
wonkipop |
![]()
Post
#3
|
Advanced Member ![]() ![]() ![]() ![]() Group: Members Posts: 4,819 Joined: 6-May 20 From: north antarctica Member No.: 24,231 Region Association: NineFourteenerVille ![]() ![]() |
Word. Clipped rom Wikipedia: The first commercial electronicially controlled manifold injection system was the Electrojector developed by Bendix and was offered by American Motors Corporation (AMC) in 1957.[34][35] Initial problems with the Electrojector meant only pre-production cars had it installed so very few cars were sold[36] and none were made available to the public.[37] The EFI system in the Rambler worked well in warm weather, but was difficult to start in cooler temperatures.[38] Chrysler offered Electrojector on the 1958 Chrysler 300D, DeSoto Adventurer, Dodge D-500, and Plymouth Fury, arguably the first series-production cars equipped with an EFI system.[39] The Electrojector patents were subsequently sold to Bosch, who developed the Electrojector into the Bosch D-Jetronic. The D in D-Jetronic stands for Druckfühlergesteuert, German for "pressure-sensor controlled"). The D-Jetronic was first used on the VW 1600TL/E in 1967. This was a speed/density system, using engine speed and intake manifold air density to calculate "air mass" flow rate and thus fuel requirements. Bosch superseded the D-Jetronic system with the K-Jetronic and L-Jetronic systems for 1974, though some cars (such as the Volvo 164) continued using D-Jetronic for the following several years. The L-Jetronic uses a mechanical airflow meter (L for Luft, German for "air") that produces a signal that is proportional to volume flow rate. This approach required additional sensors to measure the atmospheric pressure and temperature, to calculate mass flow rate. L-Jetronic was widely adopted on European cars of that period, and a few Japanese models a short time later. wow. amc. never knew that. they were an interesting company weren't they. i'd have to bone up on it all again, but think i remember that america did all the heavy lifting work on the development of the transistor? important to remember germany had a context for being enthusiast about fuel injection, admittedly high pressure style mechanical injection - from WW2 on. perhaps reason for bosch grabbing the bendix tech. its all a bit of an german/american partnership post WW2 too. space program etc. the best of both worlds. wasn't the bosch proto D installed on a mercedes as a bosch skunk works project? but merc hesitated so they drove down the road to VW who jumped straight in. |
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 13th July 2025 - 08:09 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |