 Splitting Impeller housing, Update: tins and flaps with headers? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| rfinegan |
 Jul 26 2021, 02:51 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,130 Joined: 8-February 13 From: NC Member No.: 15,499 Region Association: MidAtlantic Region 
 |
I have my impeller house apart for cleaning and it appears there were alignment pins for the front and back halves . How many are there? I have 2 pins around the impeller itself. There seems to be holes in the perimeter for pins too? Please review and advise so I can dig up some more as needed
Best Robert Diagram does not show the housing in 2 pieces  |
   |
 
|
  |
Replies
| rfinegan |
Jul 27 2021, 04:20 AM
Post
#2
|
|
Senior Member Group: Members Posts: 1,130 Joined: 8-February 13 From: NC Member No.: 15,499 Region Association: MidAtlantic Region
|
What are people in the "914 Word" doing with cars with no heat and headers?
(NOT the Thermostat Flaps) But I do have to relocate my stat away from the headers. NO lower tins? What about the flaps on the impeller housing? The little pins will fall out Anyone block this off for more flow around the heads and cylinders ? Or just let them BLOW |
|
|
|
| Shivers |
Jul 27 2021, 08:06 AM
Post
#3
|
|
Senior Member Group: Members Posts: 3,167 Joined: 19-October 20 From: La Quinta, CA Member No.: 24,781 Region Association: Southern California |
QUOTE(rfinegan @ Jul 27 2021, 03:20 AM)  What are people in the "914 Word" doing with cars with no heat and headers? (NOT the Thermostat Flaps) But I do have to relocate my stat away from the headers. NO lower tins? What about the flaps on the impeller housing? The little pins will fall out Anyone block this off for more flow around the heads and cylinders ? Or just let them BLOW I blocked them off. I made small wood plugs to fit, used Vulkem calking to keep them in place. Not all calking will handle the heat and exposure. I'd probably just make an aluminum block off plate if I did it over again. |
 |
|
Posts in this topic
rfinegan Splitting Impeller housing Jul 26 2021, 02:51 PM
rfinegan I pulled another housing apart and it looks to hav... Jul 26 2021, 03:48 PM bkrantz My fuzzy memory agrees with 2 pins. Jul 26 2021, 07:54 PM rfinegan AWESOME..>That matches what I have too
Thanks ... Jul 27 2021, 04:17 AM Dave_Darling I have heard arguments that the cooling setup was ... Jul 27 2021, 05:27 PM worn
I have my impeller house apart for cleaning and i... Jul 27 2021, 08:28 PM Nogoodwithusernames I've been told that Jake Raby does not block o... Jul 28 2021, 01:55 PM
worn
I've been told that Jake Raby does not block ... Jul 28 2021, 05:44 PM Mark Henry
I've been told that Jake Raby does not block... Jul 29 2021, 09:04 AM Dave_Darling ... in my life the laws of physics aren’t just o... Jul 29 2021, 02:10 PM 930cabman I was considering blocking off the small rectangul... Jul 28 2021, 02:59 PM mate914 Looking at the snail shaped fan or fractal. The ai... Jul 29 2021, 08:05 AM davep The heating system does offer a fair amount of res... Jul 29 2021, 10:28 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th November 2025 - 07:00 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.