 My first rust repair, Looking for some direction |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Rhodes71/914 |
 Jan 7 2005, 06:07 PM
Post
#1
|
|
Glacier  Group: Members Posts: 1,374 Joined: 8-August 04 From: End of the Road, Alaska Member No.: 2,482  |
It's time for my first rust repair project.
Thankfully I got lucky when I got lucky when I bought my car, it doesn't have a lot of rust, just a couple of spots. I am going to tackle the worst first so I can get the refreshed 2.0 in. Here is a photo of the spot. It is foward of the batt. tray and right in the lower front corner of the engine bay. I removed a funky metal patch that the previous owner had riveted and thrown some kind of gunk on to seal it up, How much more should I cut away? and then ... (IMG:http://homepage.mac.com/seanrh1/.Pictures/914%20Pics/rust%20hole.jpg) |
   |
 
|
  |
Replies
| Rhodes71/914 |
Jan 8 2005, 04:13 PM
Post
#2
|
|
Glacier Group: Members Posts: 1,374 Joined: 8-August 04 From: End of the Road, Alaska Member No.: 2,482 |
Trekkor - thanks for the link I knew I had seen a recent thread but couldn't remeber which it was, some good info there.
Dan - you better watch what you offer, you could find yourself taking a long drive. Ed- thanks for the advice. Just so ya'll know most of the welding I have done is good ol' fashioned stick welding with pretty thick steal on commercial fishing boats, with some wire feed aluminum welding (but not much of that). A friend of mine with quite a bit of welding experience will be helping me out. Now if I could just find the time. |
|
|
|
Posts in this topic
Rhodes71/914 My first rust repair Jan 7 2005, 06:07 PM
elocke When I learned to weld and practiced enough to tak... Jan 7 2005, 10:49 PM Root_Werks Hey Sean! Well, it really doesn't look to... Jan 8 2005, 11:14 AM trekkor Here's my take, as I just finished this one la... Jan 8 2005, 03:23 PM Rhodes71/914 Some cutting done. Kinda tuff getting the cut-off ... Jan 13 2005, 09:52 PM trekkor Way to go!
I think our cars rust areas are ab... Jan 14 2005, 12:15 AM skline Just my take on this, maybe I have done it wrong i... Jan 14 2005, 12:41 AM trekkor Just used a #60 grit lap sander disc on my grinder... Jan 14 2005, 01:20 AM spare time toys Never and I can not say NEVER enough start to work... Jan 14 2005, 07:43 AM trekkor Or you can be like me, and do it [i]all in four we... Jan 14 2005, 09:45 AM Rhodes71/914 Trekkor can you email your templates? That would b... Jan 14 2005, 10:42 AM type11969 take a real good look down into that long to see w... Jan 14 2005, 11:00 AM davep They don't call that the hellhole for nothing.... Jan 14 2005, 12:01 PM JCG Sean
Keep digging. My car had a "small" hole unde... Jan 14 2005, 12:10 PM Rhodes71/914 Jim if it looked that bad for me I think I might c... Jan 14 2005, 04:40 PM
SpecialK Sean, I'm going to be dealing with the same me... Jan 14 2005, 06:07 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 07:13 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.