 Firewall bolt cap, Missing In Action? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
Model Specific Information
914/4: 70 71 72 73 74 75 76 914/6: 70 71 72
| StarBear |
 Nov 12 2021, 03:42 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,907 Joined: 2-September 09 From: NJ Member No.: 10,753 Region Association: North East States 
 |
Might anyone know a) if there should be some sort of trim cap on the bolt that is exposed through the firewall pad and located just forward of the main relay board (see photo) and b) if so, its part number? I don't see it in any of the parts diagram and I'm not sure what it's connecting to on/in the firewall. (IMG:style_emoticons/default/confused24.gif)
Mine's been "open" for several decades but not sure if there was a cap that fell off or it's just "open". At least I've finally gotten around to cleaning it up (after the photo).  |
   |
 
|
  |
Replies
| Van B |
Jul 8 2022, 03:07 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,612 Joined: 20-October 21 From: Maryland Member No.: 26,011 Region Association: None
|
What is incorrect?
|
|
|
|
| StarBear |
Jul 8 2022, 07:37 PM
Post
#3
|
|
Senior Member Group: Members Posts: 1,907 Joined: 2-September 09 From: NJ Member No.: 10,753 Region Association: North East States
|
QUOTE(Van B @ Jul 8 2022, 05:07 PM)  What is incorrect? The wipers! Will send pic tomorrow. The “bent” arm one goes on the drivers side; the straight arm one goes on the passenger side. When correct, the geometry makes sense. Also, a 1.8 made just a few vin numbers before mine is here and has the charcoal can in the front. Will send pics on that thread tomorrow, too. FYI, @wonkipop |
|
|
|
| wonkipop |
Jul 8 2022, 09:08 PM
Post
#4
|
|
Advanced Member Group: Members Posts: 4,396 Joined: 6-May 20 From: north antarctica Member No.: 24,231 Region Association: NineFourteenerVille
|
QUOTE(StarBear @ Jul 8 2022, 07:37 PM) QUOTE(Van B @ Jul 8 2022, 05:07 PM) What is incorrect? The wipers! Will send pic tomorrow. The “bent” arm one goes on the drivers side; the straight arm one goes on the passenger side. When correct, the geometry makes sense. Also, a 1.8 made just a few vin numbers before mine is here and has the charcoal can in the front. Will send pics on that thread tomorrow, too. FYI, @wonkipop good another data point. get the K# as well as the VIN if you can. the derelict one in a back yard that was posted up a couple of weeks ago was a engine bay can with an earlier VIN than 2 charcoal can ones i found last year. i'd say there is a bit of overlap going on if you used VIN numbers, but K#s might tell a slightly different story. unfortunately the derelict one had no K# info with it. ps - i thought everyone knew about the wipers. (IMG:style_emoticons/default/biggrin.gif) must be common mistake to get them the wrong way around. hope you all had some fun on your run. must be amusing to be able to get a swarm of 914s all in one place. |
|
|
|
Posts in this topic
StarBear Firewall bolt cap Nov 12 2021, 03:42 PM
wonkipop mine is like that.
always has been.
think its mean... Nov 12 2021, 04:10 PM
StarBear
mine is like that.
always has been.
think its mea... Nov 12 2021, 06:01 PM StarBear Hobo finish hack: Here's what I did:
1. Before... Nov 14 2021, 04:09 PM wonkipop
Hobo finish hack: Here's what I did:
1. Befor... Nov 15 2021, 08:29 PM StarBear @wonkipop . Yep. Dat true! Heeeheeee :D Nov 16 2021, 07:30 AM infraredcalvin Hobo finish??? Sheesh, I would have sprayed some f... Jul 3 2022, 02:58 PM Van B I don't know how I missed this thread, but @S... Jul 8 2022, 10:57 AM StarBear
I don't know how I missed this thread, but [... Jul 8 2022, 01:31 PM Van B Unfortunately no. My car is about to be torn apart... Jul 8 2022, 03:06 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th June 2024 - 04:23 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.