 Easy way to install Master cylinder reservoir tubes |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| pcdarks |
 Apr 7 2021, 06:58 PM
Post
#1
|
|
Member  Group: Members Posts: 80 Joined: 22-June 13 Member No.: 16,037 Region Association: None  |
I was reading somewhere here about how difficult it is to get the tubes from the reservoir into the grommets on the master cylinder. I greased them up with caliper assembly lube and they slipped in as easy as a 50 year ol....well lets just say they went right in.
|
   |
 
|
  |
Replies
| mgphoto |
Oct 3 2022, 02:02 PM
Post
#2
|
|
"If there is a mistake it will find me" Group: Members Posts: 1,375 Joined: 1-April 09 From: Los Angeles, CA Member No.: 10,225 Region Association: Southern California |
When attaching the rubber grommets after installing the stainless steel washers, I use a long needle nose pliers with a 90 degree bend, I cover the jaws with green body tape, to prevent marring.
Position the grommet in the correct opening with the pipe attached, avoid squeezing the pliers to much, using the bend in the pliers pull down on the grommet until it pops into place. Takes maybe 3 minutes to do. |
|
|
|
Posts in this topic
pcdarks Easy way to install Master cylinder reservoir tubes Apr 7 2021, 06:58 PM
mepstein Did you include the metal washers? Apr 7 2021, 07:11 PM
pcdarks
Did you include the metal washers?
I'm confu... Apr 7 2021, 07:20 PM infraredcalvin
Did you include the metal washers?
I'm conf... Apr 7 2021, 07:25 PM pcdarks
[quote name='pcdarks' post='2906394' date='Apr 7 ... Apr 7 2021, 07:45 PM pcdarks There are no washers. The incoming lines are flare... Apr 7 2021, 07:16 PM mepstein
There are no washers. The incoming lines are flar... Apr 7 2021, 07:34 PM JLance67
There are no washers. The incoming lines are fla... Oct 24 2022, 08:10 AM bdstone914
[quote name='pcdarks' post='2906393' date='Apr 7... Oct 24 2022, 08:37 AM JLance67
[quote name='JLance67' post='3037465' date='Oct 2... Oct 27 2022, 12:52 AM Superhawk996
It's like they slowly apply until they compl... Oct 27 2022, 06:31 AM infraredcalvin I’ve done this several times and have struggled ... Apr 7 2021, 07:23 PM bkrantz Assuming this is for a replacement MC, I think the... Apr 7 2021, 07:43 PM pcdarks
Assuming this is for a replacement MC, I think th... Apr 7 2021, 07:46 PM bbrock I also used brake assembly lube and pulled them on... Apr 7 2021, 07:53 PM pcdarks
I also used brake assembly lube and pulled them o... Apr 7 2021, 08:11 PM bbrock
[quote name='bbrock' post='2906407' date='Apr 7 2... Apr 7 2021, 08:32 PM mepstein
I also used brake assembly lube and pulled them ... Apr 7 2021, 08:43 PM Chris914n6 My new 914rubber M/C leaks too. The tubes seem a l... Oct 3 2022, 01:56 PM Morrie
My new 914rubber M/C leaks too. The tubes seem a ... Oct 3 2022, 02:22 PM 914werke :popcorn: Apr 7 2021, 08:16 PM bbrock Oh, and I'm a huge fan of 914Rubber and have b... Apr 7 2021, 08:53 PM Morrie
Oh, and I'm a huge fan of 914Rubber and have ... Oct 3 2022, 12:19 PM bbrock
Oh, and I'm a huge fan of 914Rubber and have... Oct 3 2022, 01:04 PM Morrie
Hi Brent,
I realize this is a super old post. A... Oct 3 2022, 02:18 PM IronHillRestorations If the grommets went in really easily, the washers... Apr 7 2021, 09:14 PM pcdarks
If the grommets went in really easily, the washer... Apr 9 2021, 04:49 PM wysri9 Another thread that maybe saved my life.....I need... Apr 7 2021, 10:27 PM brant hopefully there are metal washers under your newly... Apr 8 2021, 08:31 AM Steve I just went through this. The rubber bushings wer... Apr 8 2021, 08:49 AM willieg Before I bought a 19 mm master cylinder from 914Ru... Oct 3 2022, 03:02 PM Morrie
Before I bought a 19 mm master cylinder from 914R... Oct 3 2022, 03:05 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 27th October 2025 - 05:26 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.