 Smoke, Smoke |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Boothy |
 Apr 20 2025, 06:35 PM
Post
#1
|
|
Member  Group: Members Posts: 108 Joined: 17-January 19 From: Abington, MA Member No.: 22,805 Region Association: North East States  |
Cheers all!
Sorry, but I again need to ask for help. New engine blowing smoke. 1.7 punched out to 2.0 with a big bore kit. Cam, Weber 40s. It started and ran pretty well late last fall. Used engine break-in oil as recommended. No smoke but sluggish acceleration -fine at high RPM. With the warm weather (finally) I swapped out the Weber jets to the recommended .50, 1.50, and 1.95. Ran it up to 3300 with a timing light. I remembered I did static timing but not dynamic. Now it sounds pretty good but I'm seeing light blue smoke and a really black exhaust. I don't think the jets were that different but no markings so not sure. My immediate horror was a broken ring -I really don't want to pull the engine again. It idles fine and sounds strong. I'll do a compression check. When it idles, there's no smoke. When I bring it up, it begins to smoke a little. Then it's consistent—no horrible but noticeable. It sounds strong. It idles nicely at a 1000 and revs up fine. I'm hesitant to push it until I figure out what's going on. Changed the oil to 20W-50. Could it be, with the soot on the tailpipe, my jets are wrong? Stretch I know but hopeful. Heads are new so the oil in the guides shouldn't be an issue. As always, thanks in advance! |
   |
 
|
  |
Replies
| TheCabinetmaker |
Jun 9 2025, 04:56 PM
Post
#2
|
|
I drive my car everyday Group: Members Posts: 8,339 Joined: 8-May 03 From: Tulsa, Ok. Member No.: 666 |
What is 1.7 "punched out to 2L"?
|
|
|
|
| Boothy |
Jun 9 2025, 06:12 PM
Post
#3
|
|
Member Group: Members Posts: 108 Joined: 17-January 19 From: Abington, MA Member No.: 22,805 Region Association: North East States |
QUOTE(TheCabinetmaker @ Jun 9 2025, 05:56 PM)  What is 1.7 "punched out to 2L"? The big bore kit from AA. Hoping I didn't get dog shit rings. Compression test soon will tell. I used the good break-in oil. Did the rev at whatever to seat the rings. It was fine for a long time. Now smoking. IDK. People wonder why I drink. |
|
|
|
Posts in this topic
Boothy Smoke Apr 20 2025, 06:35 PM
bdstone914 Oil smoke? Black run rich smoke? I would start wit... Apr 21 2025, 02:11 AM VaccaRabite Possible issues:
Rings have not yet seated.
Overfi... Apr 21 2025, 06:00 AM Boothy Thank you for the detail! Will do all in order... Apr 21 2025, 07:17 AM Eric_Shea Compression test first. If everything is good the... Apr 21 2025, 08:17 AM Nogoodwithusernames My rebuild stock-ish 1.7 was breaking in and runni... Apr 21 2025, 09:15 AM Boothy An update...
Thank you all for the advice.
It... Jun 9 2025, 07:32 AM emerygt350 I found my driver's side is a pain too. I use... Jun 9 2025, 01:13 PM
Boothy Thank you! I'll try the gasket maker. I, t... Jun 9 2025, 02:12 PM emerygt350 I have the 96mm pistons/sleeves from AA. They hav... Jun 9 2025, 06:39 PM brant How many miles on the engine since the build? Jun 10 2025, 10:47 AM Boothy
How many miles on the engine since the build?
N... Jun 23 2025, 09:14 AM sixnotfour
you need to drive accell and let decel load ring... Jun 23 2025, 09:54 AM VaccaRabite Hey Boothy,
its is likely that your rings are not... Jun 23 2025, 12:21 PM 930cabman or overfilled Jun 23 2025, 12:44 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th July 2025 - 08:34 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.