 Karmann Chassis Number in Trunk |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| friethmiller |
 Jun 27 2025, 10:19 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 936 Joined: 10-February 19 From: Austin, TX Member No.: 22,863 Region Association: Southwest Region 
 |
Does anyone know the height of the lettering used for the chassis number in the trunk? Or, could measure it, please? I'm trying to replicate the Karmann number on my LE but this trunk was replaced by the PO. I have a 4mm, 6mm, and 10mm punch set. So, it'll probably be 8mm (IMG:style_emoticons/default/blink.gif)
 Thanks. |
   |
 
|
  |
Replies
| friethmiller |
Jun 30 2025, 08:30 AM
Post
#2
|
|
Senior Member Group: Members Posts: 936 Joined: 10-February 19 From: Austin, TX Member No.: 22,863 Region Association: Southwest Region
|
Well I won't call it a complete failure but....
 It's not easy to get a hammer in here and get the numbers straight. I used a piece of tape as a bottom line, which helped but I couldn't hit with enough force to really make a good imprint. Probably needs to be done before the piece goes in the car. (IMG:style_emoticons/default/confused24.gif) If I can't get something behind it to actually imprint the numbers better, I may abandon the effort. I'm thinking I might use a bottle jack and some wood blocks to provide support from underneath. If so, I'll grind/hammer what I did and start over. |
|
|
|
Posts in this topic
friethmiller Karmann Chassis Number in Trunk Jun 27 2025, 10:19 AM
ClayPerrine The original trunk floor is still in Elwood, so I ... Jun 27 2025, 11:55 AM
friethmiller
The original trunk floor is still in Elwood, so I... Jun 27 2025, 12:01 PM Jamie
Does anyone know the height of the lettering used... Jun 27 2025, 12:07 PM friethmiller
They are 10mm in my original 1973 teener. :head... Jun 27 2025, 12:57 PM ClayPerrine I just walked out into the garage and took this:
... Jun 27 2025, 01:57 PM friethmiller
I just walked out into the garage and took this:
... Jun 28 2025, 04:39 AM rgalla9146
I just walked out into the garage and took this:... Jun 28 2025, 11:32 AM Puebloswatcop Fred, you should have known they were 10 mm. They... Jun 27 2025, 04:59 PM Montreal914 One question could be: what is the width? :idea: Jun 27 2025, 08:57 PM KELTY360 I can confirm 10mm height and 7 digit number plus ... Jun 28 2025, 11:30 AM davep This is the 1970 location, and the 1970 914/6 seri... Jun 28 2025, 04:04 PM ClayPerrine Apparently the number on the six chassis was stamp... Jun 30 2025, 04:10 AM Jamie
Well I won't call it a complete failure but..... Jun 30 2025, 10:43 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st July 2025 - 02:48 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.