 O-ring oil pump, Picture needed |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Chad911sc |
 Sep 26 2025, 01:28 PM
Post
#1
|
|
Member  Group: Members Posts: 188 Joined: 24-September 24 From: Florida Member No.: 28,374 Region Association: South East States  |
So on my new 2056 I have been getting low oil pressure numbers after the oil gets hot. I have 85 lbs at start up, but after it gets to 220, I’m only getting 5lbs at idle and 45lbs at rev to around 5grand. I do have an external filter/fan combo that could be contributing to my issue. After it gets past 190 the valve opens up and lets the hot oil into the external fan cooler combo. I changed out the 26mm oil pump to the 30mm offered on LN engineering, but still same problem. The reason I ask about O-ringing my pump is because when I changed out the pump to the bigger one, I noticed that my case was gouged in 2 places where the pump press fits into the case. I’m thinking that this could be my culprit. That the oil is just pushing back into the sump from those digs in the case halves. I also ordered the piece from Tangerine racing to replace my oil valve spring inside the case, as I still am using the stock spring as of now. I’m going to pull the pump back out of the case this weekend and I will post a couple pics of the gouges in the case.
I was wanting to know exactly where this o-ring would go on the pump, so I can take it to my machine shop and have a grove beveled into it. One more thing out of the equation to solve this problem. |
   |
 
|
  |
Replies
| Jack Standz |
Sep 27 2025, 04:56 PM
Post
#2
|
|
Senior Member Group: Members Posts: 551 Joined: 15-November 19 From: Happy Place (& surrounding area) Member No.: 23,644 Region Association: None 
|
QUOTE(Chad911sc @ Sep 28 2025, 04:03 AM)  The pump had a pretty good leak from the gasket between the pump and the case, so I thought while I had it out, I would just put in a larger one due to the extra hose and cooler. I guess I’ll find out in a week when I get the Tangerine part. Interested to know if anyone has had good or bad reviews of the "Dual-O-Ring" Pro Pump Only at Lowbugget.com! that Superhawk996 identified. Sounds like it might prevent oil leaks from the cover. Anyone used one? (Have a couple of Gene Berg hard anodized type 1 oil pumps with O-rings in the pump bodies, but never used an oil pump with an o-ring on the cover). https://www.lowbugget.com/oil_pump.html |
|
|
|
| cgnj |
Sep 27 2025, 05:18 PM
Post
#3
|
|
Senior Member Group: Members Posts: 693 Joined: 6-March 03 From: Medford, NJ Member No.: 403 Region Association: None
|
I have a single o ring pump waiting to be autopsied. After I torqued the case tru bolts, the drive gear would not fit into the pump body. Until I figure out if I screwed the pooch, I wouldn't take the chance on having a second point of failure.
|
 |
|
Posts in this topic
Chad911sc O-ring oil pump Sep 26 2025, 01:28 PM
cgnj I'm going to pm you about this. Sep 26 2025, 02:55 PM JamesM 1. Which 30mm pump?
2. Were the clearances in spe... Sep 26 2025, 04:35 PM Superhawk996 All T1 pump bodies are undersized vs proper T4 pum... Sep 26 2025, 08:34 PM Chad911sc Yes I ordered the Tangerine racing oil relief valv... Sep 27 2025, 06:15 AM Geezer914 I have a 26 mm pump from CB performance. 80 lbs.c... Sep 27 2025, 08:29 AM
cgnj @Geezer914 Did the CB pump require any prep work ... Sep 27 2025, 10:35 AM Chad911sc That’s what I had in my engine when I built it, ... Sep 27 2025, 11:59 AM Superhawk996
Obviously that wasn’t the problem because the 3... Sep 27 2025, 02:42 PM Chad911sc You are correct as usual!
At the time when I ... Sep 27 2025, 03:03 PM |
3 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
1 Members: cgnj
|
Lo-Fi Version | Time is now: 27th September 2025 - 07:17 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.