 Ugghh... I think I did the oil strainer nut thing?! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| TRP |
 Nov 22 2025, 02:52 PM
Post
#1
|
|
Member  Group: Members Posts: 132 Joined: 2-September 23 From: Morgan Hill, CA Member No.: 27,559 Region Association: None 
 |
Ugh.... I think I did what I wasnt supposed to do! I had to drain 1 qt of oil out of my engine because I over filled it. I drained some oil and went to tighten things up. With my torque wrench set to 8 ft lbs I started to torque things back down (up?) and about two turns in the was a loud ping... and the nut was loose again. I wasnt anywhere near 8ft/lbs.
I have a 1.8 with the 914 Werks tuna can. Am I destined to have this motor torn down for a repair? I snugged it up and took the car out for a test drive, fully expecting to dump 3.75q of Brad Penn on the toad. 15 minutes later... no drips... no gushers. What should I do here? Ted |
   |
 
|
  |
Replies
| TRP |
Nov 22 2025, 04:08 PM
Post
#2
|
|
Member Group: Members Posts: 132 Joined: 2-September 23 From: Morgan Hill, CA Member No.: 27,559 Region Association: None
|
Sorry for the confusion. The Tuna Can bolt/formerly the oil strainer bolt.
I drove it another 10 miles, one tiny drop under the car. I'm gutted, because I'm pretty sure that I popped that stud out of the boss in the case. If I'm trying to find a positive here, I guess I found my donor 1.8 for the core rebuild for a 2056. |
|
|
|
Posts in this topic
TRP Ugghh... I think I did the oil strainer nut thing?! Nov 22 2025, 02:52 PM
fiacra
Ugh.... I think I did what I wasnt supposed to do... Nov 22 2025, 03:15 PM FlacaProductions Drain plug or tuna can bolt? Nov 22 2025, 03:21 PM wonkipop must have been stripped prior?
or your torque w... Nov 22 2025, 03:25 PM TRP Well, damn. There is now a 4" collection of o... Nov 22 2025, 05:47 PM
wonkipop
Well, damn. There is now a 4" collection of ... Nov 22 2025, 10:13 PM TRP
Well, damn. There is now a 4" collection of... Nov 22 2025, 10:20 PM wonkipop
[quote name='wonkipop' post='3233867' date='Nov 2... Nov 22 2025, 10:34 PM Jack Standz Sorry to hear about your motor. As you know, it... Nov 22 2025, 07:51 PM TRP Ugh. I dont think I was the nitial cause, It has t... Nov 22 2025, 08:21 PM Jack Standz The boss is on the left/driver's side of the m... Nov 22 2025, 09:33 PM Jack Standz 2nd photo Nov 22 2025, 09:34 PM sixnotfour Use an inch pound torque wrench ,,, and or have yo... Nov 22 2025, 09:55 PM wonkipop take the vette out for a drive. put a smile back... Nov 22 2025, 10:36 PM |
7 User(s) are reading this topic (7 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd November 2025 - 01:57 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.