 Used pistons and cylinders value |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jmargush |
 Jan 19 2026, 07:22 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 500 Joined: 8-June 04 From: Goshen, IN Member No.: 2,176  |
Is there a value/ market for used pistons and cylinders?
Particularly 1.8 Or is it just as good to scrap them for aluminum and steel $? |
   |
 
|
  |
Replies
| didenpx |
Jan 22 2026, 08:37 AM
Post
#2
|
|
Member Group: Members Posts: 127 Joined: 1-September 23 From: Usa Member No.: 27,556 Region Association: North East States 
|
I'm so glad this topic came up!
I'm looking at re-commissioning a stroker engine with 103mm cylinders that I acquired along with some parts cars and miscellaneous stuff. I've been mulling cylinder options (recondition the ones that came with the engine, buy new cast iron cylinders from one of the usual suspects, or open the wallet for Nickies). I'm assuming that the cast iron cylinders that are available now are likely all coming from the same source somewhere in the PRC. Aside from the usual considerations of the longevity of large displacement cast iron cylinders, what is the consensus on quality of manufacture, etc.? |
|
|
|
Posts in this topic
jmargush Used pistons and cylinders value Jan 19 2026, 07:22 PM
friethmiller
Is there a value/ market for used pistons and cyl... Jan 19 2026, 08:50 PM sixnotfour $$$ Jan 19 2026, 10:11 PM
jmargush
$$$
$$$ ?
Did th... Jan 20 2026, 12:50 PM friethmiller
$$$
$$$ ?
Did t... Jan 21 2026, 10:18 PM Superhawk996
Cost effective? Compared to what? The cheap/in... Jan 22 2026, 09:52 AM porschetub Scrap sorry ...thats the way it is ,cheers. Jan 21 2026, 06:11 PM Jamie
Scrap sorry ...thats the way it is ,cheers.
I... Jan 21 2026, 09:44 PM Ninja If I was going to build a T4 and didn't have t... Jan 22 2026, 08:27 AM Ninja The original poster's question...
If you NEED... Jan 22 2026, 08:56 AM 930cabman I have been running AA pistons/cylinders for sever... Jan 22 2026, 09:59 AM Shivers I have been known to carve pistons from time to ti... Jan 22 2026, 10:29 AM Ninja
Cost effective? Compared to what? The cheap/i... Jan 22 2026, 10:37 AM Ninja
I have been known to carve pistons from time to t... Jan 22 2026, 10:38 AM Jack Standz
Is there a value/ market for used pistons and cy... Jan 22 2026, 10:50 AM Superhawk996
The metallurgy and quality of original cylinders... Jan 22 2026, 11:07 AM mepstein My opinion, unless you have a use for them now, th... Jan 22 2026, 10:59 AM Ninja :agree:
Yes, the Chinese HAVE the technology to ... Jan 22 2026, 11:48 AM Superhawk996
If it says "Made in China" it needs t... Jan 22 2026, 01:14 PM Aayala I was also going to ask this question, but in my c... Jan 22 2026, 12:48 PM Jack Standz
The metallurgy and quality of original cylinder... Jan 22 2026, 01:13 PM Ninja Ninja #1 golden rule!
There are ALWAYS EXCEPT... Jan 22 2026, 02:13 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th March 2026 - 07:39 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.