 Convert back to D Jet Fuel Injection-, Wire harnessess- Injector Ground |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| young55961 |
 Jun 18 2026, 02:34 PM
Post
#1
|
|
Member  Group: Members Posts: 53 Joined: 15-March 18 From: Arcadia Member No.: 21,972 Region Association: Southern California  |
I have a question about the ECU wiring harness.
There are three pairs of white wires with female spade terminals on the harness. I believe they are the ground wires for the fuel injectors, but I can't find where they are supposed to connect. Should these wires be connected to the negative (-) terminal of the ignition coil? If anyone has a photo showing the correct connection, I would really appreciate it. Thank you! |
   |
 
|
  |
Replies
| young55961 |
Nov 1 2026, 12:22 PM
Post
#2
|
|
Member Group: Members Posts: 53 Joined: 15-March 18 From: Arcadia Member No.: 21,972 Region Association: Southern California |
I'm trying to test-run my 1975 Porsche 914 2.0L D-Jetronic engine outside the car, and I have a few questions about the relay board and wiring harness.
 The two pins inside the red square both show 12V with the ignition ON. Is this correct? I also tested the other two pins, but neither appears to be connected to ground.  It seems that the wiring arrangement may be incorrect. From my understanding: - **#31** should be ground. - **#24 and #19** should receive 12V. - **#18** should receive 12V temporarily while cranking the engine. Am I understanding these connections correctly? I want to make sure I supply power to the correct terminals before attempting to start the engine outside the car. Also, I'm not sure whether I should start a new thread for these questions or continue posting in this thread. Any advice would be greatly appreciated. Thanks! |
|
|
|
Posts in this topic
young55961 Convert back to D Jet Fuel Injection- Jun 18 2026, 02:34 PM
brant There was supposed to be a three prong connector o... Jun 18 2026, 02:46 PM JeffBowlsby 2 of the three pairs are injector grounds. The th... Jun 18 2026, 02:46 PM
young55961
2 of the three pairs are injector grounds. The t... Jun 18 2026, 02:52 PM Ishley Here is what you’re looking for in the yellow ci... Jun 18 2026, 08:12 PM young55961
Here is what you’re looking for in the yellow c... Jun 19 2026, 10:54 AM DC_neun_vierzehn
Here is what you’re looking for in the yellow c... Jun 19 2026, 03:54 PM young55961
[quote name='Ishley' post='3261972' date='Jun 18 ... Jun 19 2026, 08:17 PM Jack Standz It's easy enough to get one. Here's one e... Jun 19 2026, 03:44 PM Ishley Mine is a '72 1.7 that I rebuilt into a 2056. ... Jun 19 2026, 04:25 PM Dave_Darling Mine is further back, right by the flywheel end of... Jun 19 2026, 09:27 PM DC_neun_vierzehn
Mine is further back, right by the flywheel end o... Jun 22 2026, 05:27 AM robkammer Mine is right at the top of the case split at the ... Jun 23 2026, 05:38 AM friethmiller :popcorn:
Observing... learning. I'll be do... Jun 23 2026, 07:33 AM GregAmy From my Microsquirt build notes.
T4-I
.75 and .5m... Nov 1 2026, 12:31 PM Dave_Darling I'm pretty sure that #31 should get grounded b... Nov 1 2026, 07:04 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st November 2026 - 09:18 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.