|
|

|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| rick 918-S |
Nov 19 2026, 09:23 PM
Post
#1
|
|
Hey nice rack! -Celette ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 21,388 Joined: 30-December 02 From: Now in Superior WI Member No.: 43 Region Association: Northstar Region
|
I have a stock 2.0 with Euro pistons and a lightened flywheel Other than that, Stock FI cam. No other changes. I ordered some 40MM ITB's but then realized my intakes are for 48-50 MM Carbs. Any think I could run 48-50 MM ITB's on a stock high compression 2.0?
|
![]() ![]() |
| JamesM |
Nov 20 2026, 09:23 AM
Post
#2
|
|
Caretaker of 914s - Master of Fuel Injection ![]() ![]() ![]() ![]() Group: Members Posts: 2,372 Joined: 6-April 06 From: Kearns, UT Member No.: 5,834 Region Association: Intermountain Region |
I have a stock 2.0 with Euro pistons and a lightened flywheel Other than that, Stock FI cam. No other changes. I ordered some 40MM ITB's but then realized my intakes are for 48-50 MM Carbs. Any think I could run 48-50 MM ITB's on a stock high compression 2.0? People always seem to wind up going to big on throttle bodies. Bigger is not always better and with EFI often it is worse. I think you will be fine with 40mm on a 2.0. Maybe not optimal and you may have to run Alpha-N tuning as they are still on the large side and the bigger you go the less vacuum signal resolution you have if you intend to run speed-density. You will also want to make sure you have the best linkage and synchronization possible as ITBs are far more sensitive to imbalanced linkage than carbs and the bigger you go the worse that gets. If anyone wants an explanation why let me know. 48-50mm I think would be an absolute nightmare. 44s are already rough to deal with. To reinforce what @GregAmy said, when comparing to carbs, at least in terms of power achievable, compare to the venturi size, NOT the throttle plate size. Here is another data point to consider, Porsche ran 38mm ITBs that tapered down to 36 on the 3.0RS MFI motor which had similar bore and stroke to the 2.0 type 4. Stock 2.0 (including high compression euro) runners are also 36mm There is math you can do to get a rough estimate of where you want to be, but in general a 40mm ITB bore will handle ~61hp per cylinder and increases are exponential with 48s being good for about 100hp per cylinder. Bigger doesn't get you more power but it does make it harder to drive, harder to tune, and potentially less low end torque. I like to aim for the minimum necessary size. I have to ask what is making you go with ITBs in the first place though? In general I find them worse in most ways to a single throttle body setup and don't even consider them unless you are 2.3 or larger with a healthy cam as that is where you start to run into limits of what is currently available for single TB setups. |
rick 918-S Anyone have an opinion on ITB size for a 2.0 Nov 19 2026, 09:23 PM
sixnotfour This guy been doing em longer than most.. Have see... Nov 19 2026, 11:00 PM
rick 918-S Thanks. I have everything with the except I messed... Nov 20 2026, 04:39 AM
GregAmy My opinion? With stock 2L D-Jet cam and more compr... Nov 20 2026, 07:42 AM
Superhawk996
*My tilt for a street car is always too small vs... Nov 20 2026, 08:51 AM
VaccaRabite :agree:
If you think about carbs they are necked d... Nov 20 2026, 08:21 AM
JamesM As a side note, I designed and build the EFI syste... Nov 20 2026, 10:25 AM![]() ![]() |
|
Lo-Fi Version | Time is now: 21st November 2026 - 01:18 AM |
| All rights reserved 914World.com © since 2002 |
|
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |