 I think maybe I... overtightened, give me the bad news |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| brer |
  Jul 5 2005, 08:05 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,555 Joined: 10-March 05 From: san diego Member No.: 3,736 Region Association: None  |
Put the rocker assemblies back on my heads and drove home to san diego.
got very loud rocker noises coming from the engine re adjust the valves. drive it for a little while and bigger clacking noise and starting to lose power. (IMG:http://www.914world.com/bbs2/html/emoticons/sad.gif) I think i *effed* it up installing the new studs and then torqing the rocker assembly nuts with my old torque wrench. thought i seated the studs properly, and torqued the nuts right, but now the valves dont seem to be holding an adjust. so what the worst that could have happened? stripped the studs from the heads right? |
   |
 
|
  |
Replies
| brer |
Jul 5 2005, 09:12 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,555 Joined: 10-March 05 From: san diego Member No.: 3,736 Region Association: None |
they were the original holes.
I'm thinking the loud valve noise that prompted the tinkering may have been a prelude to my current problem. Every time i adjusted them they would be quiet for a few days then get noisy again. No worries though. (IMG:http://www.914world.com/bbs2/html/emoticons/smile.gif) I was thinking of pulling the motor to figure out the geometry and do some rust repair anyway, this will just be another rung on the ladder. Damn it was running good too. i'm going to have a beer. (IMG:http://www.914world.com/bbs2/html/emoticons/beer.gif) |
|
|
|
Posts in this topic
brer I think maybe I... overtightened Jul 5 2005, 08:05 PM
McMark Time to pull of the rocker assemblies and really g... Jul 5 2005, 08:42 PM brer any way to tell if the stud is starting to pull ou... Jul 5 2005, 08:44 PM Dr Evil Yes, look at how much is sticking out past the nut... Jul 5 2005, 08:59 PM V6914 Jul 5 2005, 09:55 PM bd1308 you mean like grinding down a cam....how often doe... Jul 5 2005, 10:13 PM V6914 Jul 5 2005, 10:21 PM V6914 Jul 5 2005, 11:02 PM brer I've only adjusted the valves once since i got... Jul 5 2005, 11:44 PM V6914 Jul 6 2005, 12:42 AM ArtechnikA Jul 6 2005, 05:34 AM bd1308 Jul 6 2005, 06:24 AM DonTraver Hey Bear, once you get the engine out, you could b... Jul 6 2005, 07:56 AM brer went out and turned her over to listen again.
the... Jul 6 2005, 07:50 PM Elliot Cannon Jul 7 2005, 10:20 PM brer it aint fixed yet! http://w... Jul 7 2005, 11:09 PM Jake Raby I have the new German wavy washers in stock..... I... Jul 7 2005, 11:16 PM brer ok, i'm not giving up yet.
ht... Jul 7 2005, 11:30 PM Jake Raby NEVER give up...
If you want something with a Sub... Jul 7 2005, 11:37 PM brer i still have this to play with.
I'm talking a... Jul 7 2005, 11:45 PM Jake Raby 60 was a good year...
Its needs a MassIVe 4...
O... Jul 8 2005, 12:00 AM brer I was thinking of rebuilding the original 36hp.
W... Jul 8 2005, 09:21 AM brer so i put the new rocker assembly's on with .03... Jul 15 2005, 03:41 PM brer BTW- it lives! going for a little drive. ... Jul 15 2005, 08:08 PM bd1308 I love beetles.....it would be so cool to have one... Jul 15 2005, 08:14 PM
brer all i have to say now is.
h... Jul 15 2005, 10:03 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 05:20 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.