 Removing a complete rear control arm, BEST way to remove the cv from the trans |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Gint |
 Oct 14 2005, 05:26 PM
Post
#1
|
|
Mike Ginter  Group: Admin Posts: 16,083 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains   |
I know I can get it off, done it way to many times. But why oh why is it such a bitch to get these damn things off? Does anyone have a really, really, really clean way to get them off easily? I have a nice complete used rear arm with drive shaft and everything ready for a swap.
Oh, and, do any of my local gang have a cv joint gasket handy? It's the one thing out of all the crap I forgot to order that I absolutely must have to get the car back on the road this weekend. |
   |
 
|
  |
Replies
| Spoke |
Oct 15 2005, 03:26 PM
Post
#2
|
||
|
Jerry Group: Members Posts: 6,991 Joined: 29-October 04 From: Allentown, PA Member No.: 3,031 Region Association: None 
|
I made one from a piece of thick exhaust gasket material from my FLAPS. To make sure the thing was circular, I used Word on the PC to draw 2 circles, one inside the other, printed it and used it for a stencil to cut the gasket. Spoke |
||
|
|
|
||
Posts in this topic
Gint Removing a complete rear control arm Oct 14 2005, 05:26 PM
olav I just removed mine last Friday.
I undid the hex ... Oct 14 2005, 05:31 PM Gint Oct 14 2005, 05:33 PM SLITS Tap a flat blade screwdriver into the mating flang... Oct 14 2005, 05:38 PM ArtechnikA off? small impact wrench, sharp chisel to separat... Oct 14 2005, 05:51 PM BMartin914 Mike,
I *might* have a gasket. I have a bag full ... Oct 14 2005, 06:09 PM Gint It's off. Once I got all of the control arm m... Oct 14 2005, 06:58 PM Gint Mmmm... Love sushi. And sake.
Anywho... Insi... Oct 14 2005, 09:35 PM Gint At least the hole isn't ovaled. Note the crun... Oct 14 2005, 09:37 PM Gint Old... Oct 14 2005, 09:37 PM Gint The new. The rotor, caliper, and cheasy studs wil... Oct 14 2005, 09:39 PM Gint Ben! I need that gasket. Nobody has one on t... Oct 15 2005, 09:13 AM Gint Oct 15 2005, 10:10 AM davep Wow, I've never seen a control arm bushing loo... Oct 15 2005, 10:11 AM SLITS Oct 15 2005, 10:19 AM Cap'n Krusty Oct 15 2005, 10:57 AM Gint Oct 15 2005, 02:10 PM goose2 get some gasket paper at FLAPS and make one if you... Oct 15 2005, 02:26 PM Gint Oct 15 2005, 02:36 PM redshift Oct 15 2005, 03:27 PM jsteele22 Oct 16 2005, 03:41 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th June 2024 - 07:39 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.