Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Metal shapers, How do you roll the edge, of a 3" hole for an exposed gas cap?
neo914-6
post Dec 14 2005, 11:52 PM
Post #1


neo life
*****

Group: Members
Posts: 5,086
Joined: 16-January 03
From: Willow Glen (San Jose)
Member No.: 159
I looked at alot of cars at the dismantler but the round gas cap holes are usually 5" diameter to allow you to stick your hand in. The smaller ones like on the early Rabbit have a flange to mount the gas filler.


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies
rick 918-S
post Dec 15 2005, 12:10 AM
Post #2


Hey nice rack! -Celette
***************

Group: Members
Posts: 21,239
Joined: 30-December 02
From: Now in Superior WI
Member No.: 43
Region Association: Northstar Region
Make an inside and out side die set out of 3/8" steel. Use a 3/4" or 1" bolt (big bolt) and an impact to pull the two parts together. Or just use a hammer and dolly....
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Posts in this topic
neo914-6   Metal shapers, How do you roll the edge   Dec 14 2005, 11:52 PM
Bleyseng   thats stamped and it takes a large metal press to ...   Dec 14 2005, 11:55 PM
Andyrew   Have you tried with a hammer and dolley to make th...   Dec 14 2005, 11:59 PM
rick 918-S   Make an inside and out side die set out of 3/8" st...   Dec 15 2005, 12:10 AM
goose2   make a sheet metal ring the same dia as the hole, ...   Dec 15 2005, 12:11 AM
sixnotfour   I did both methods, this picture welded ring , the...   Dec 15 2005, 12:26 AM
sixnotfour   other   Dec 15 2005, 12:44 AM
Andyrew   rear?? Whats that go to? Oil?   Dec 15 2005, 12:49 AM
sixnotfour   peterson oil tank,different ht...   Dec 15 2005, 12:52 AM
Travis Neff   I am with Rick, a belling tool is ticket. If you ...   Dec 15 2005, 01:15 AM
airsix   http://w...   Dec 15 2005, 10:42 PM
jonwatts   Oooh, very neo   Dec 15 2005, 11:35 PM
goose2     Dec 15 2005, 11:51 PM
jonwatts   Tequipment   Dec 15 2005, 11:59 PM
lotus_65   <...   Dec 16 2005, 01:32 PM
neo914-6   I'll have to find a locking gas cap then...   Dec 16 2005, 03:16 PM
iamchappy   This is how mine looks with the door open.   Dec 16 2005, 04:05 PM
iamchappy   I topped off the stock cap with a wheel centercap.   Dec 16 2005, 04:06 PM
neo914-6   Nice touch, how about a clear door? ...   Dec 16 2005, 05:29 PM
neo914-6   ...   Dec 16 2005, 06:51 PM
lotus_65   ...   Jan 14 2006, 02:41 AM
neo914-6     Jan 14 2006, 03:01 AM
jasons     Jan 14 2006, 05:50 PM

 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

- Lo-Fi Version Time is now: 2nd April 2026 - 03:20 PM
Invision Power Board v9.1.4 © 2026  IPS, Inc.
...
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...