Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Cutting out the rust, cuttoff tool?
swl
post Mar 25 2006, 08:22 PM
Post #1


Senior Member
***

Group: Members
Posts: 1,409
Joined: 7-August 05
From: Kingston,On,Canada
Member No.: 4,550
Region Association: Canada
I bought myself a compressor and el cheap tool kit. I was kind of hoping that the cutoff tool would be the right thing for cutting out the cancer. Had a go at it today but this tool was useless. No torque at all - stalled with very little pressure - hardly any sparks. There is an adjuster on it that seems to throttle the air supply. Played with that a bit but it didn't really make any difference.

So do I have a faulty tool or just the wrong tool for the job?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies
Joe Bob
post Mar 25 2006, 09:38 PM
Post #2


Retired admin, banned a few times
***************

Group: Members
Posts: 17,427
Joined: 24-December 02
From: Boulder CO
Member No.: 5
Region Association: None
Electric grinder or sawzall is the best....cheap and you can beat them to death.

I have found that air tools aren't as good unless you have a tank as big as Fat Albert and 220volt.....
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Posts in this topic
swl   Cutting out the rust   Mar 25 2006, 08:22 PM
Lou W   Is the compressor putting out enough pressure to r...   Mar 25 2006, 09:00 PM
grasshopper   http://www.914world.com/bbs2/h...   Mar 25 2006, 09:03 PM
lapuwali   Cutoff tools and grinders need a LOT of air. You ...   Mar 25 2006, 09:06 PM
swl   Don't think it's supply problem. The comp...   Mar 25 2006, 09:07 PM
grasshopper     Mar 25 2006, 09:10 PM
swl   Thanks James. I thought of the dremel but was thi...   Mar 25 2006, 09:17 PM
736conver     Mar 25 2006, 09:25 PM
Joe Owensby   I am using a 4 1/2 inch electric grinder . Cost a...   Mar 25 2006, 09:34 PM
Lou W   This is the Saw that I use, Ingersol Rand model 42...   Mar 25 2006, 10:02 PM
Lou W   I then use the Ingersoll Rand model 301 for clean ...   Mar 25 2006, 10:06 PM
riverman   Go with the electric grinder (from experience) and...   Mar 25 2006, 10:48 PM
Rand   There's a big difference between air and elect...   Mar 26 2006, 12:19 AM
Michael Oberg   Looks like everyone has covered the basics and ans...   Mar 26 2006, 04:29 AM
dinomium   cheaper than the IR saw, I am getting this one: Ea...   Mar 26 2006, 12:04 PM
dinomium   cheaper than the IR saw, I am getting this one: Ea...   Mar 26 2006, 12:04 PM
kwales   It just depends on what tool is needed for the job...   Mar 26 2006, 01:05 PM
degreeoff   I agree more tools = better coverage....I have a c...   Mar 26 2006, 01:45 PM
swl   Thanks everyone. Lots of good info there. The cu...   Mar 26 2006, 05:26 PM

 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

- Lo-Fi Version Time is now: 5th July 2025 - 04:59 AM
Invision Power Board v9.1.4 © 2025  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...