 Height Adjustment & Travel, Why parallel? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Joseph Mills |
 Feb 27 2003, 12:14 AM
Post
#1
|
|
on a Sonoma diet now...  Group: Members Posts: 1,482 Joined: 29-December 02 From: Oklahoma City, OK Member No.: 39  |
My 914 goes to the shop next week for alignment: 1.5 to 2 degrees neg camber front, 2 to 2.5 neg rear with 1/16" toe-out front, 1/16" toe-in rear. Tires are Hoosier A3S03's.
I have found a few posts that seem to indicate that when the A-arms and trailing arms are parallel to the ground, you have maximized your cars height. Is this in fact, correct? If so, why is this level preferred? If you go below this height is suspension geometry adversely effected? How much wheel travel is left at this point? Joseph '75 914 2.0L AX bound |
   |
 
|
  |
Replies
| Joseph Mills |
Feb 28 2003, 08:34 AM
Post
#2
|
|
on a Sonoma diet now... Group: Members Posts: 1,482 Joined: 29-December 02 From: Oklahoma City, OK Member No.: 39 |
Brad,
"I have NEVER set a car up with more negative in the rear than the front." Are you referring to track/race cars only, are does this include AX for you? I have no experience with higher speeds of track/race, but do have some experience in AX (and still learning). It's my understanding that what can work for an AX can be way too loose for track speeds. That being said, I know many autocrossers that run more negative camber in back than front. Would like to hear your views. Joseph |
|
|
|
Posts in this topic
Joseph Mills Height Adjustment & Travel Feb 27 2003, 12:14 AM
ChrisReale I dont think yo have maximized the height when the... Feb 27 2003, 12:39 AM Brad Roberts Answers will very...but. I feel its important beca... Feb 27 2003, 12:42 AM Joseph Mills Chris,
Sorry. Poor choice of words (brainfart typo... Feb 27 2003, 12:48 AM Brad Roberts I knew what you meant.
B Feb 27 2003, 12:49 AM airsix Sorry, no answer. Just extending the question a b... Feb 27 2003, 12:50 AM Brad Roberts Raised spindle is the way to go.. but its very ver... Feb 27 2003, 12:59 AM Dave_Darling Limiting the camber change is one of the reasons f... Feb 27 2003, 11:46 AM drew365 Joseph; I'm curious about the numbers you post... Feb 27 2003, 01:59 PM Brad Roberts Each car is going to be different. Bent arms tweak... Feb 27 2003, 02:07 PM airsix <... Feb 27 2003, 02:39 PM J P Stein He,he.....this is great stuff.
Prior to my mods, ... Feb 27 2003, 02:59 PM Joseph Mills Drew,
My settings are the initial settings I hope ... Feb 27 2003, 02:59 PM Brad Roberts I have NEVER set a car up with more negative in th... Feb 27 2003, 04:36 PM drew365 J.P.; No shims were used in the rear. He corner ba... Feb 27 2003, 06:41 PM airsix <... Feb 27 2003, 06:50 PM Jeroen do some searching on Pelican
there's an articl... Feb 27 2003, 08:29 PM seanery C'mon Jeroen!
a bic pen?
It's gettin... Feb 27 2003, 08:32 PM drew365 Didn't you ever watch McGeyver? I think he... Feb 27 2003, 09:00 PM Jeroen hey, he's asking for cheap and if it works... ... Feb 27 2003, 09:02 PM si2t3m DID SOMEONE SAY CHEAP????
''You will nee... Feb 27 2003, 09:32 PM ChrisReale Brad Roberts Drew,
I hope you didnt think the "Ricky Racer" wa... Feb 28 2003, 02:22 AM J P Stein Ben:
Caster.
When the car is going straight ahea... Feb 28 2003, 04:41 AM
drew365 Brad; You can call me Ricky Racer anytime! Jus... Feb 28 2003, 09:23 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 5th June 2025 - 01:20 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.