 started first real work on my 71, bodywork....Yay!!! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| geniusanthony |
 Sep 9 2006, 07:10 PM
Post
#1
|
|
Its a brand new "Chrome-sicle"  Group: Members Posts: 517 Joined: 12-December 05 From: Alexandria,VA Member No.: 5,266 Region Association: MidAtlantic Region  |
started out by stripping all four corners about a month ago, then bought my fuches, but since then I have kinda stalled out mostly due to work obligations, had to go to NE Washington for the forest fires for the last three weeks or so.
before I left I bought 16x6 and 7's and found that some stretching would be necessary in the rear. I have always liked soft flares anyway... but as follows is 1) as delivered 2-4) stripped and pounding started on the rear fenders Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| geniusanthony |
Sep 9 2006, 07:23 PM
Post
#2
|
|
Its a brand new "Chrome-sicle" Group: Members Posts: 517 Joined: 12-December 05 From: Alexandria,VA Member No.: 5,266 Region Association: MidAtlantic Region |
#4 close up again...and problem area which i need advice for...
the part in red is bowed under a little bit and I am not getting enough stretch from front to rear to add the width inside the fender opening. the curvature top to bottom i like but again i cannot get the width i need , like the actual fender detail isnt pushing out for the width i need..oh by the way 225/50's on 16x7's in back..i need about another inch or so Attached thumbnail(s) 
|
|
|
|
Posts in this topic
geniusanthony started first real work on my 71 Sep 9 2006, 07:10 PM
geniusanthony #2 stretched Sep 9 2006, 07:15 PM geniusanthony #3 close up on fender Sep 9 2006, 07:16 PM JPB Lots of stroking on that sheet metal bro. Good wo... Sep 9 2006, 07:21 PM geniusanthony dont worry i know i am not close to being done (bu... Sep 9 2006, 07:28 PM Lou W Looking good, looks like you'll end up with so... Sep 9 2006, 07:34 PM geniusanthony my goal is more rounded to flow into the shoulders... Sep 9 2006, 07:54 PM Lou W No, its not mine...however there are people here t... Sep 9 2006, 07:57 PM geniusanthony BUMP Sep 10 2006, 04:37 AM JPB If you use a brazing tip on a torch and the samlle... Sep 10 2006, 06:14 AM John Kelly Hi Tony,
You need to use a hammer and dolly to sm... Sep 10 2006, 07:20 AM geniusanthony John, thank you for your quick reply to my earlier... Sep 12 2006, 03:26 AM geniusanthony side note all I am trying to intall in the rear is... Sep 12 2006, 10:24 PM John Kelly Hi Tony,
It takes many stretch and smooth session... Sep 13 2006, 08:06 AM geniusanthony haven't had the oppportunity to wokr lately or... Sep 14 2006, 08:50 AM
John Kelly |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 09:59 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.
| All rights reserved 914World.com © since 2002 |
|
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |