 Help with cutting holes for -6 oil tank., would like to cut holes now while looking for an oil tank. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jj83118 |
 Jan 6 2007, 12:22 PM
Post
#1
|
|
Newbie  Group: Members Posts: 33 Joined: 12-May 05 From: Colorado Springs, CO Member No.: 4,066 Region Association: None  |
Help!
I'm in the middle of repairing the longitudinal rust on my 914-6 conversion and I'd like to cut all the required holes for installing a -6 oil tank. I have most of the left rear quarter-panel off and I'd like to cut the holes while I have easy access. I can plainly see where most of the holes should go, but I don't know where to cut the unmarked hole. I could also use some help cutting the required hole in the engine tray sheet metal. Any help is appreciated. Thanks, Jim |
   |
 
|
  |
Replies
| dr914@autoatlanta.com |
Jan 6 2007, 12:59 PM
Post
#2
|
|
914 Guru Group: Members Posts: 7,893 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
QUOTE(jj83118 @ Jan 6 2007, 10:22 AM)  Help! I'm in the middle of repairing the longitudinal rust on my 914-6 conversion and I'd like to cut all the required holes for installing a -6 oil tank. I have most of the left rear quarter-panel off and I'd like to cut the holes while I have easy access. I can plainly see where most of the holes should go, but I don't know where to cut the unmarked hole. I could also use some help cutting the required hole in the engine tray sheet metal. Any help is appreciated. Thanks, Jim Not to toot my own horn but I do have a precise cutting template in my 914-6 conversion guide. It is pretty obvious where the holes need to be drilled (absolutely none in the engine shelf on the up to 72 cars) but it is the size that matters! |
|
|
|
Posts in this topic
jj83118 Help with cutting holes for -6 oil tank. Jan 6 2007, 12:22 PM
mikez
Help!
I'm in the middle of repairing the... Jan 6 2007, 12:53 PM jj83118 The problem is I don't have the tank yet (I... Jan 6 2007, 03:58 PM mikez Cut the ones you can see, do the finish work later... Jan 6 2007, 04:02 PM GeorgeRud Kudos to the Auto Atlanta templates, they were a p... Jan 6 2007, 04:17 PM
Superhawk996
Only caveat, if you're using an aftermarket ... Aug 7 2020, 09:03 AM thesey914 Didn't Trek have a template file to print off... Jan 24 2007, 04:37 PM Eric_Shea JJ... if you can make the trip you can look at my ... Jan 24 2007, 05:52 PM trekkor try this.
I believe Dan Root sent me this a coupl... Jan 26 2007, 11:03 PM Tdskip
try this.
I believe Dan Root sent me this a coup... Aug 7 2020, 08:53 AM John I have one of those too. From the same source. Jan 26 2007, 11:12 PM mepstein If you are using Ben’s / 914-6werkshop tank, itâ... Aug 7 2020, 10:43 AM Tdskip
If you are using Ben’s / 914-6werkshop tank, it... Aug 7 2020, 03:22 PM mb911 I suggest templating my tanks to make it even clos... Aug 8 2020, 05:58 AM Tdskip
I suggest templating my tanks to make it even clo... Aug 8 2020, 06:00 AM Mark Henry
I suggest templating my tanks to make it even clo... Aug 8 2020, 12:42 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th June 2024 - 03:57 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.