 Vanagon digifant distributor on ebay, perfect for megasquirt conversion |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Cano |
 Jan 4 2007, 08:24 PM
Post
#1
|
|
Member  Group: Members Posts: 110 Joined: 29-September 04 From: Goshen, KY Member No.: 2,854 Region Association: None  |
Check it out. Hall sensor, perfect for megasquirt conversion -- drops right in type 4 case. I'm not the seller -- just thought it was a good deal that someone may need.
http://cgi.ebay.com/ebaymotors/Vanagon-86-...1QQcmdZViewItem |
   |
 
|
  |
Replies
| DNHunt |
Jan 12 2007, 06:06 PM
Post
#2
|
|
914 Wizard? No way. I got too much to learn. Group: Members Posts: 4,099 Joined: 21-April 03 From: Gig Harbor, WA Member No.: 598 |
Yep
Thought about it. I even have the coils. The issue has been controlling 4 coil drivers and 4 injection drivers. The router bord will let that happen with CAN communication. The 36-1 trigger wheel is fine for the crank position and the Hall effect dizzy can provide the cam position. The problem is the router board has been at least 2 years and I haven't seen it yet. The truth is it probably wouldn't be a noticable improvement from the system I have cause getting the last 5% of performance out of any system takes a good tumer and a dyno. I'm a tinkerer and just enjoy the doing and I don't have that much experience tuning . I can get close but, I'm sure there is more available. Beyond that, once it was tuned I'd only leave it alone for a week or so and then I'd start playing again. I'd just enjoy opening the engine lid and watching people try to figure out the puzzle. Dave Dave |
|
|
|
Posts in this topic
Cano Vanagon digifant distributor on ebay Jan 4 2007, 08:24 PM
brer Please elaborate. Jan 4 2007, 11:58 PM
Mueller
Please elaborate.
for MS, you need a signal to ... Jan 5 2007, 01:11 AM Paul Illick You can do the same thing with a sensor on a tooth... Jan 5 2007, 06:04 AM brer
You can do the same thing with a sensor on a toot... Jan 5 2007, 10:26 AM Mueller
You can do the same thing with a sensor on a too... Jan 5 2007, 10:49 AM Cano I am going to use this same distributor for my meg... Jan 5 2007, 10:41 AM Cap'n Krusty Anyone interested in a used Digifant distributor s... Jan 5 2007, 10:50 AM tdsmoonchild
Anyone interested in a used Digifant distributor ... Jan 7 2007, 11:11 AM rdauenhauer
Cap'n? would those be new or rebuilt? Jan 7 2007, 11:53 AM tdsmoonchild :bump: For the Cap'n Jan 12 2007, 11:30 AM DNHunt Cam Sensor for COP ignition and sequential injecti... Jan 12 2007, 04:38 PM rdauenhauer :bump: Again... My intrest is piqued. Jan 12 2007, 05:38 PM Zimms Dave,
Your running EDIS, aren't you? Have you... Jan 12 2007, 05:47 PM Zimms I am looking forward to getting into it myself. I ... Jan 12 2007, 08:21 PM DNHunt It requires one to control their right foot. I cou... Jan 13 2007, 08:15 AM Zimms Understood. Thansk a lot for the info!
Mark Jan 13 2007, 08:25 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 10:40 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.