Optimizing D-Jetronic, Brainstorming.... |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Optimizing D-Jetronic, Brainstorming.... |
pbanders |
Apr 18 2007, 04:28 PM
Post
#1
|
Senior Member Group: Members Posts: 939 Joined: 11-June 03 From: Phoenix, AZ Member No.: 805 |
Here are my thoughts on a systematic approach to optimizing D-Jetronic for a specific stock or near-stock engine - just putting this down and looking for comments:
Comments? If the intake system has been significantly modified (e.g. different cam, big valves, etc.), then to do the dyno procedure correctly, an assessment of the VE changes would need to be made, and the ECU daughter-card SC circuit would need mods - but this is beyond a reasonable approach for most people. |
pbanders |
Apr 19 2007, 10:46 AM
Post
#2
|
Senior Member Group: Members Posts: 939 Joined: 11-June 03 From: Phoenix, AZ Member No.: 805 |
If adding a lot of ballast resistance makes your 914 run better, then do it! Be aware, however, that adding too much may make the mixture vary once the engine is fully warmed up, possibly causing drivability problems.
This chart is from my ECU web page: (IMG:http://members.rennlist.com/pbanders/CTCVoutBallast.gif) It shows the relationship between the Cylinder Temperature Compensation (CTC) circuit output voltage and the resistance of the TS2 (also called the CHT sensor) plus any ballast resistance. Higher values of CTC Vout translate to richer mixtures. The blue trace is for an 037 ECU with an 012 TS2 and no ballast, the other traces show the effect of increasing ballast, up to 500 ohms. The temperature ranges on the chart were deduced from calibrating the resistance values of the TS2 to actual temperatures. What you see is that if you add between 50 and 270 ohms of ballast, you richen the mixture only through cold start and warm-up. If you add 500 ohms, now the mixture varies once the engine is fully warmed up. The ECU circuit is designed to linearize the TS2 characteristic and to cut off its effect once the engine is fully warmed up. |
computers4kids |
Apr 19 2007, 05:53 PM
Post
#3
|
Love these little cars! Group: Members Posts: 2,443 Joined: 11-June 05 From: Port Townsend, WA Member No.: 4,253 Region Association: None |
If adding a lot of ballast resistance makes your 914 run better, then do it! Be aware, however, that adding too much may make the mixture vary once the engine is fully warmed up, possibly causing drivability problems. What you see is that if you add between 50 and 270 ohms of ballast, you richen the mixture only through cold start and warm-up. If you add 500 ohms, now the mixture varies once the engine is fully warmed up. The ECU circuit is designed to linearize the TS2 characteristic and to cut off its effect once the engine is fully warmed up. The chart was very helpful understanding what the resistance does...especially after warm-up. Since I currently have 270 ohms...I'm only seeing the effects during warm-up...it will be interesting when I crank up the pot between 270-500+ how that will effect warm running. Do you suspect the 043 MPS responds simarily to the 037 MPS? Thanks |
Lo-Fi Version | Time is now: 10th June 2024 - 11:19 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |