 Rebuilding the 2056, To tight? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 72914S |
 May 28 2007, 07:56 AM
Post
#1
|
|
love this shot  Group: Members Posts: 1,290 Joined: 10-July 03 From: Pensacola,Fl. Member No.: 900 Region Association: South East States  |
Well I finally got all the pieces for the rebuild.Yesterday Joe(Redneck Racer) came over,we planed to check the deck height.We put the crank in(those bearing pins are hard to line up).The rear main seemed real tight,finally got the dowel pin right and the crank turns freely.For the mock up I put the other case half on and tighted it up,now the crank won`t turn at all.Joe thinks I need line boreing.Let me say that this engine spun the rear main and cooked # 3 piston.Anyone out there have any thoughts. Am I doing something wrong.
|
   |
 
|
  |
Replies
| Joe Ricard |
May 29 2007, 06:48 AM
Post
#2
|
|
CUMONIWANNARACEU Group: Members Posts: 6,811 Joined: 5-January 03 From: Gautier, MS Member No.: 92 |
We pulled the pin and tried it that way, no difference. The outer diameter of the bearing DON"T FIT THE CASE.
I agree that the the case bearing saddle has collapsed. If you had seen the carnage of when Barry pulled the motor apart some of you may have gotten sick to your stomach. What Barry really needs is for someone to hook him up with a good case. |
|
|
|
Posts in this topic
72914S Rebuilding the 2056 May 28 2007, 07:56 AM
Bleyseng Check the clearances in each bearing with some pla... May 28 2007, 10:16 AM kwales Bearing bores don't usually get smaller. My g... May 28 2007, 11:30 AM McMark Pull it apart and inspect the main bearings. Prob... May 28 2007, 04:27 PM r_towle I agree, and obviously you need to take it apart.
... May 28 2007, 05:26 PM McMark Aren't the main bearings designed with a certa... May 28 2007, 05:29 PM r_towle Not that I know of, but Jake will know.
If that wa... May 28 2007, 05:33 PM McMark I'm definitely not talking about 0.125" o... May 28 2007, 05:37 PM r_towle never bothered me..
But, I dont do as many as Jake... May 28 2007, 05:57 PM 72914S The crank has been pro ground(20 over)& balanc... May 28 2007, 07:37 PM Jake Raby This case MUST have the main bores measured both w... May 28 2007, 07:38 PM shaggy
It sounds to me like you may have "missed a ... May 28 2007, 07:48 PM
ptravnic
jake's video does help even though it dosent ... May 28 2007, 08:06 PM 72914S I have Jakes video quess I`ll watch it again. May 29 2007, 06:20 AM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 08:05 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.