 pic of lines exiting tunnel? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| slim72914 |
 Aug 18 2007, 10:46 PM
Post
#1
|
|
Member  Group: Members Posts: 153 Joined: 4-July 07 From: Mesa, AZ Member No.: 7,874  |
I am trying to install my stainless steel fuel lines on my 72 4 and have encountered some strange stuff where the lines exit the tunnel in to the engine compartment. anyone have a pic of how it should be??? this is how mine is.
 Not too sure whats up with the 1/4" steel plate on the clutch cable... Needless to say I have work to do before installing the stainless lines... |
   |
 
|
  |
Replies
| Type 4 Unleashed |
Aug 18 2007, 11:05 PM
Post
#2
|
|
CREATIVE TYPE lV ENGINEERING Group: Retired Members Posts: 787 Joined: 20-June 04 From: Aliso Viejo, ca Member No.: 2,231 Region Association: None |
It would look like the rest of the firewall, the plate was a make shift fix, the weld on the clutch tube to the firewall may have broke loose.
You'll have to remove the plate and check it out and repair it properly. |
|
|
|
Posts in this topic
slim72914 pic of lines exiting tunnel? Aug 18 2007, 10:46 PM
slim72914 I went back out and continued to take fuel lines a... Aug 19 2007, 12:00 AM orange914 hope this might help
Aug 19 2007, 01:10 AM orange914 RE: pic of lines exiting tunnel? Aug 19 2007, 01:11 AM
slim72914
Yes that helps alot! Ill have to make a p... Aug 19 2007, 01:25 AM Phoenix-MN Here's another angle that might help (with Tan... Aug 19 2007, 07:49 AM jasons So do you even have the tube that runs through the... Aug 19 2007, 09:45 AM rhodyguy there's a sawsall party in colorado today. if ... Aug 19 2007, 10:17 AM So.Cal.914
there's a sawsall party in colorado today. if... Aug 19 2007, 11:15 AM Bartlett 914 Here is a picture of my car showing the tubes in t... Aug 19 2007, 10:30 AM slim72914 It was indeed very poorly fixed once... There is n... Aug 19 2007, 10:59 AM rhodyguy the party is mentioned/detailed in the classifieds... Aug 19 2007, 11:34 AM dinomium
the party is mentioned/detailed in the classified... Aug 21 2007, 01:36 PM slim72914 I like to do stuff the wrong way so ill machine me... Aug 20 2007, 11:49 PM Bartlett 914 The repair I made on mine as shown in the picture ... Aug 21 2007, 01:20 PM John Here is a picture of mine. Sorry it's not a r... Aug 21 2007, 03:56 PM slim72914 OK I got to digging around again last night and fo... Aug 21 2007, 10:08 PM Bartlett 914 Yes you need the tube! It must be welded to th... Aug 22 2007, 08:58 AM slim72914 So what is the most important part of the clutch t... Aug 23 2007, 12:55 AM Bartlett 914 The missing section of the tube sure complicates t... Aug 23 2007, 07:12 AM slim72914 I planned on making my patch out of stainless stee... Aug 23 2007, 08:52 AM Bartlett 914
I planned on making my patch out of stainless ste... Aug 23 2007, 09:19 AM slim72914 Yes it is broken off at the front too.. it is just... Aug 23 2007, 02:43 PM Bartlett 914 Go back and look at the picture I posted. You can ... Aug 23 2007, 03:29 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th May 2025 - 07:10 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.