 Welders: If you had to choose one...? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Danny_Ocean |
 Oct 21 2007, 01:31 PM
Post
#1
|
|
Member  Group: Members Posts: 170 Joined: 27-June 07 From: Fort Lauderdale, FL Member No.: 7,846 Region Association: South East States  |
I have yet to learn to weld. I would like to purchase (and learn on) a welder that will be most useful to the average "car guy"...welding sheetmetal, repairing broken mounts, adding brackets to rollbars/frames, etc. Nothing exotic, just basic repairs for the average mechanic. My shop has 220v if that matters. (IMG:style_emoticons/default/welder.gif)
|
   |
 
|
  |
Replies
| Dr. Roger |
Oct 21 2007, 05:07 PM
Post
#2
|
|
A bat out of hell. Group: Members Posts: 3,944 Joined: 31-January 05 From: Hercules, California Member No.: 3,533 Region Association: Northern California |
thick steel plate.
you need the penetration power to get deeper than what 110V will give. i tried to use my 110V MIG for a custom winch mount for my tacoma and it wouldn't get the depth that i needed unless i ground a deep "V" at my joints and filled, swipe by swipe, like LvSteveH probably had to do to get his strong welds using 110V. that's when i switched over to my 220, reverse polarity, stick welder. you can get a 220V MIG and just make sure you get a box with infinite amperage control. that way you can bring the power way down for your light projects and crank it up for your larger welds. nothing better than gas shielding so don't take short cut using flux core. BTDT. Good luck. =) |
|
|
|
Posts in this topic
Danny_Ocean Welders: If you had to choose one...? Oct 21 2007, 01:31 PM
Vacca Rabite You don't need 220. All you need is a 115 vol... Oct 21 2007, 01:51 PM Danny_Ocean Will a 115v unit produce strong enough welds for t... Oct 21 2007, 02:22 PM ejm You might have a problem doing those repairs on he... Oct 21 2007, 03:02 PM scotty b This will do ANYHTING you will need on your car an... Oct 21 2007, 03:20 PM
LvSteveH These are great for just about anything on a 914 a... Oct 21 2007, 03:37 PM Danny_Ocean I won't be exceeding my limitations. If there ... Oct 21 2007, 03:59 PM Spoke
So...115v MIG sounds like the deal, yes?
Yep, i... Oct 21 2007, 04:49 PM Danny_Ocean
Yep, it works well for me. I was hesitant to get ... Oct 21 2007, 04:56 PM dflesburg 115volt MIG
Get one with:
Variable Wire speed
T... Oct 21 2007, 05:05 PM JPB If my name had Ocean in it and had your daneros, I... Oct 21 2007, 05:18 PM Danny_Ocean
If my name had Ocean in it and had your daneros, ... Oct 21 2007, 05:23 PM bperry
Do you have a manuf./model #?
I went to the Mill... Oct 21 2007, 07:00 PM scotty b <_<
http://cgi.ebay.com/MILLER-DYNASTY-200... Oct 21 2007, 05:28 PM Danny_Ocean Thanks, but those seem a little "overkill... Oct 21 2007, 05:38 PM JPB I'm not trying to knock down any welders of wh... Oct 21 2007, 06:12 PM Gint I'm perfectly happy with my 220v Miller 175 wi... Oct 21 2007, 06:14 PM JPB 95% of all my teener welds are done with a Lincon ... Oct 21 2007, 06:23 PM Richard Casto Here is my 2 cents...
Stick vs. MIG vs. TIG
Get ... Oct 21 2007, 06:24 PM roadster fan I am not an experienced welder by any means but ea... Oct 22 2007, 01:53 AM stephenaki OK, I have been reading the thread and it is a gre... Oct 22 2007, 04:38 AM type47
Here is my question on the subject to add a tw... Oct 22 2007, 06:49 AM stephenaki
i don't think you can or should do this but ... Oct 23 2007, 02:43 AM Richard Casto
i don't think you can or should do this but... Oct 23 2007, 10:59 AM Wes V I've got a Miller MM130 mig and I can't en... Oct 22 2007, 10:52 AM Jax914 I bought the Millermatic 135 a couple of years ago... Oct 23 2007, 07:13 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 11:18 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.