 Type 1 CV Joints, Using Type 1 CV Joints |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| LotusJoe |
 Oct 26 2010, 03:46 PM
Post
#1
|
|
Europa Twink Driver  Group: Members Posts: 406 Joined: 30-November 09 From: Southern California Member No.: 11,085 Region Association: Southern California  |
Has anyone used type one CV joints? They are dimensionally the same. The type one joint does not use the gasket like the original joint. Also all the holes are the same size and will not accommodate the 10 mm roll pin.
 I made some pins that fit the stub axle and transmission flange while fitting the hole in the type 1 CV joint. That way no modification is required to either component.  I used 1211 sealant in place of the gasket.  Anyone else done this? |
   |
 
|
Posts in this topic
LotusJoe Type 1 CV Joints Oct 26 2010, 03:46 PM
kg6dxn I run 930 CV's but only because I was tired of... Oct 26 2010, 04:42 PM Cap'n Krusty Eric Shea makes/sells 914 modded T1 CV joints. (P... Oct 26 2010, 04:48 PM
Racer Chris
Eric Shea makes/sells 914 modded T1 CV joints. (... Oct 26 2010, 05:03 PM Elliot Cannon Are these CV's better? Stronger? Cheaper? W... Oct 26 2010, 07:31 PM Vacca Rabite
Are these CV's better? Stronger? Cheaper? ... Oct 26 2010, 08:02 PM Rotary'14
Are these CV's better? Stronger? Cheaper? ... Oct 26 2010, 10:08 PM LotusJoe
Are these CV's better? Stronger? Cheaper? ... Oct 27 2010, 07:08 PM Rotary'14
[quote name='Rotary'14' post='1387322' date='... Oct 27 2010, 11:17 PM LotusJoe
Even though our engines are type 4,, I NEVER said... Oct 28 2010, 05:13 PM Rotary'14 Hi Joe,, I like your simple fix.
Are your roll pi... Oct 26 2010, 09:59 PM LotusJoe
Hi Joe,, I like your simple fix.
Are your roll p... Oct 27 2010, 06:46 PM john rogers I used Eric's CV joints on my vintage race car... Oct 26 2010, 10:03 PM charliew Those pins look like steel to me. I'm sure the... Oct 26 2010, 10:07 PM Eric_Shea
They are now... :D Oct 26 2010, 11:24 PM Eric_Shea
No... I do believe Robert is wrong. McMark has ... Oct 27 2010, 08:35 PM plays with cars Great information. Always good to find alternate ... Oct 27 2010, 11:11 PM pcar916
Does anyone know how original -6 CVs factor in? ... Oct 28 2010, 08:09 AM john rogers I thought this had been beat completely before but... Oct 27 2010, 11:36 PM Eric_Shea
Same dimensionally... just a different axle and ... Oct 28 2010, 07:51 AM pcar916
How long have most peoples 914 CV's lasted?
... Oct 28 2010, 08:11 AM rick 918-S Then there are conversion cars like mine that have... Oct 28 2010, 08:13 AM pcar916
I think I may need to look at 930 joints in the f... Oct 28 2010, 08:30 AM Eric_Shea
And possibly some custom length axles. Oct 28 2010, 03:38 PM underthetire Just FYI, stainless is pretty soft, not very britt... Oct 28 2010, 04:50 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd November 2025 - 12:59 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.