 914 Jobs You Hate., Look for tips inside. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Series9 |
 Dec 23 2011, 07:41 AM
Post
#1
|
|
Lesbians taste like chicken.  Group: Members Posts: 5,444 Joined: 22-August 04 From: DeLand, FL Member No.: 2,602 Region Association: South East States  |
What are the jobs you hate to do on your 914? List them here and have other guys, hopefully, respond with their tricks to get it done more easily.
I'll start: I hate changing master cylinders because installing the supply lines in the top is a total bitch. The only tip I have on this is to disconnect the lines from the bottom of the reservoir and pull them down a little to help out. Then push them back up as you put the MC in place. It still sucks. |
   |
 
|
Posts in this topic
Series9 914 Jobs You Hate. Dec 23 2011, 07:41 AM
scotty b Hell hole
solution = .5 lb of C4 :rolleyes: Dec 23 2011, 07:44 AM sean_v8_914 ...previously repaired with chicken wire and bondo Dec 23 2011, 07:47 AM
Series9
...previously repaired with chicken wire and bond... Dec 23 2011, 07:50 AM sean_v8_914 creative wiring corrections Dec 23 2011, 07:48 AM windforfun
creative wiring corrections
:agree: :agree: ... Dec 23 2011, 10:11 PM GeorgeRud Valve adjustment on my -6!
Though I haven... Dec 23 2011, 07:55 AM BajaXJ92 Anything that isn't done within the warmth of ... Dec 23 2011, 08:10 AM URY914 MC replacement is #1.
Any work on a stock car is... Dec 23 2011, 08:41 AM type47 air box under the front cowl. Need gas tank out to... Dec 23 2011, 08:51 AM Philip W.
air box under the front cowl. Need gas tank out t... Dec 23 2011, 10:34 AM RobW
air box under the front cowl. Need gas tank out t... Dec 24 2011, 08:13 AM dlestep Fuel line replacement through center
Valve adjust... Dec 23 2011, 09:02 AM 76-914 I've stripped one 914 down to the shell, rebui... Dec 23 2011, 09:30 AM SUNAB914 Wet sanding#1
Master cylinder #2
Rear wheel bearin... Dec 23 2011, 09:33 AM Andyrew I like wet sanding... Very relaxing..
Master Cyl... Dec 23 2011, 09:37 AM SUNAB914 Rear brake lines! I agree with that one. Easy ... Dec 23 2011, 09:45 AM TurbOH Brad The worst one I ever did was a throttle cable repl... Dec 23 2011, 10:21 AM RobW
The worst one I ever did was a throttle cable rep... Dec 24 2011, 08:14 AM andys +1 for the fresh air box under the cowl; a really ... Dec 23 2011, 10:28 AM scotty b installing rear trunk torsion bars :headbang:
Yu... Dec 23 2011, 10:37 AM arkitect
installing rear trunk torsion bars :headbang:
Y... Dec 24 2011, 12:20 AM Prospectfarms
installing rear trunk torsion bars :headbang:
... Dec 25 2011, 11:24 PM Black22
What are the jobs you hate to do on your 914? Li... Dec 23 2011, 10:44 AM trfrick Replacing rear brake hard lines with the motor in... Dec 23 2011, 11:13 AM SLITS Fresh Air Box & air controls
Rubber Rear Brak... Dec 23 2011, 11:09 AM FourBlades For me it has to be solving recurrent idle jet clo... Dec 23 2011, 11:21 AM JmuRiz
For me it has to be solving recurrent idle jet cl... Dec 23 2011, 11:55 AM FourBlades
For me it has to be solving recurrent idle jet c... Dec 23 2011, 04:10 PM timofly 1. Fresh air box. Who the hell designed this mess?... Dec 23 2011, 11:39 AM JmuRiz Wiring issues due to old crash repairs and previou... Dec 23 2011, 11:54 AM rjames in no particular order
Rubber Rear Brake Lines
C... Dec 23 2011, 12:22 PM Woody Master cylinder tops the list. Dec 23 2011, 12:36 PM 9146986 I'm going to 2nd/3rd/4th/5th whatever number I... Dec 23 2011, 01:25 PM sean_v8_914 I agree most with MC hoses, electrical issues caus... Dec 23 2011, 01:31 PM sean_v8_914 for brake lines use a 11mm crow foot AKA line wren... Dec 23 2011, 01:33 PM PanelBilly Anything that I need to do Over and over to get ri... Dec 23 2011, 04:37 PM URY914 Rear trailing arm bushing change out is also a bit... Dec 23 2011, 08:29 PM DEC
Rear trailing arm bushing change out is also a bi... Dec 24 2011, 02:20 AM aharder Having to go inside to Pee :idea: I need a urinal ... Dec 24 2011, 12:10 AM Haudiosolutions Great! and I need to replace my master cylinde... Dec 24 2011, 08:11 AM RobW Anything rusted that resembles welding.
The main... Dec 24 2011, 08:23 AM Van Funny... I always hated trying to put in a battery... Dec 24 2011, 09:31 PM campbellcj 1) Anything in the pedal or lower dash area in a c... Dec 25 2011, 04:23 PM Mike D. Anything that involves removing the heat exchange... Dec 26 2011, 01:34 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 04:15 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.