 Pass side view mirror |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| SKL1 |
 Feb 3 2016, 06:14 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,605 Joined: 19-February 11 From: north Scottsdale Member No.: 12,732 Region Association: Upper MidWest 
 |
Thinking of putting a side view mirror on pass side of my '73. If I remember correctly when havin the panel off, the nuts are welded in place on the inside for the screws aren't they? Even though it would pain me to do it, you could drill from the inside through those to create the holes?
Can you just turn the mirror around to use a spare mirror from the driver's side, or it a different part number for right (pass) side? I may chicken out when it comes to drilling the holes though (IMG:style_emoticons/default/blink.gif) |
   |
 
|
Posts in this topic
SKL1 Pass side view mirror Feb 3 2016, 06:14 PM
Kansas 914
Thinking of putting a side view mirror on pass si... Feb 3 2016, 06:19 PM
Tom_T
Thinking of putting a side view mirror on pass s... Feb 3 2016, 06:42 PM Mike Fitton I use my passenger side mirror all the time while ... Feb 3 2016, 06:31 PM BeemerSteve Also, before you start to drill from the outside p... Feb 3 2016, 06:52 PM dlkawashima http://www.914world.com/bbs2/index.php?showtopic=2... Feb 3 2016, 07:50 PM Larmo63 I just did my black car. It takes ten minutes. The... Feb 3 2016, 09:22 PM raynekat As far as I know there was never a right hand driv... Feb 3 2016, 09:47 PM 76-914 I disagree about drilling from the inside. One of ... Feb 3 2016, 09:52 PM worn
Don't use cheap freaking bits and throw the d... Feb 4 2016, 10:14 AM SKL1 Great advice but my hand will probably start shaki... Feb 3 2016, 11:50 PM Darren C Use the internal punch method to mark the exact po... Feb 4 2016, 02:40 AM Tbrown4x4
[quote name='SKL1' post='2298056' date='Feb 3 201... Feb 4 2016, 03:04 AM tomrev Can you access the inner nuts without pulling out ... Feb 4 2016, 07:32 AM Larmo63 The cars were manufactured with the capture nuts i... Feb 4 2016, 08:42 AM mark04usa
The cars were manufactured with the capture nuts ... Feb 4 2016, 11:51 AM Darren C Tomrev,
Yes, remove door trim and roll up window,... Feb 4 2016, 08:55 AM tomrev
Tomrev,
Yes, remove door trim and roll up window... Feb 4 2016, 09:45 AM McMark I tend to just turn my head. So I'll be the v... Feb 4 2016, 10:08 AM worn
I tend to just turn my head. So I'll be the ... Feb 4 2016, 10:15 AM Darren C "I tend to just turn my head"
Not so e... Feb 4 2016, 10:44 AM tomrev
"I tend to just turn my head"
Not so ... Feb 4 2016, 11:00 AM worn
"I tend to just turn my head"
Not so ... Feb 4 2016, 02:30 PM Darren C Jolly good old boy, you're right up to speed w... Feb 4 2016, 02:54 PM dflesburg Yeah, definitely put one on there. Feb 4 2016, 02:59 PM Vysoc Cmon SKL1,
You are from Iowa, you can do this, I ... Feb 4 2016, 04:06 PM Dave_Darling I believe you'll find that the separation betw... Feb 4 2016, 08:35 PM ThreeV8s Does the mirror flip over (to put on the passenger... Dec 23 2017, 10:23 AM mepstein Loosen the nut under the mirror base. Sometimes th... Dec 23 2017, 10:33 AM ThreeV8s
Loosen the nut under the mirror base. Sometimes t... Dec 23 2017, 10:47 AM mepstein
Loosen the nut under the mirror base. Sometimes ... Dec 23 2017, 10:58 AM ThreeV8s
[quote name='ThreeV8s' post='2560531' date='Dec 2... Dec 23 2017, 11:04 AM mepstein
[quote name='ThreeV8s' post='2560531' date='Dec ... Dec 23 2017, 03:15 PM ThreeV8s
[quote name='ThreeV8s' post='2560535' date='Dec 2... Dec 23 2017, 11:12 PM Front yard mechanic since were hijacking this thread witch mirror belo... Dec 23 2017, 03:11 PM mepstein
since were hijacking this thread witch mirror bel... Dec 23 2017, 03:13 PM JFG Just the breakdown and instruction i needed to fli... Jun 14 2018, 11:47 AM ConeDodger I find both factory mirrors to be pretty much junk... Jun 14 2018, 12:00 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th June 2024 - 08:38 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.