 Weber 40 IDA 3bbl jet starting point for a 2.7 /6 |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| tornik550 |
 Jul 13 2016, 03:10 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,248 Joined: 29-January 07 From: Ohio Member No.: 7,486 Region Association: None  |
I have a freshly built 2.7l with 9.5:1 compression pistons. I currently have zenith 40 tin carbs with 34mm venturi's. The engine runs very well however I stumbled upon a nice set of weber 40 IDA's. I am much more familiar with weber carbs so I purchased them.
What would a good starting point for the following be? venturis idle jets main jets emulsion tubes air correction jets Also, are weber idf jets and vents interchangable with 3BBL IDA's? Thank you |
   |
 
|
Posts in this topic
tornik550 Weber 40 IDA 3bbl jet starting point for a 2.7 /6 Jul 13 2016, 03:10 PM
mskala I won't speculate on your settings as I have a... Jul 13 2016, 03:40 PM Perry Kiehl Clone Jetting shouldn't be that different from the Z... Jul 13 2016, 05:11 PM Luke M Here's a good chart with some starting points ... Jul 13 2016, 05:22 PM tornik550 Next question- Where can I find 34mm venturis? Jul 13 2016, 06:24 PM
Mark Henry
Next question- Where can I find 34mm venturis?
... Jul 13 2016, 06:58 PM 6freak
Next question- Where can I find 34mm venturis?... Jul 14 2016, 03:12 PM Mark Henry
[quote name='Mark Henry' post='2371143' date='Jul... Jul 14 2016, 03:22 PM tornik550
[quote name='Mark Henry' post='2371143' date='Ju... Jul 14 2016, 03:47 PM 6freak
[quote name='Mark Henry' post='2371143' date='Ju... Jul 15 2016, 03:24 PM 6freak
[quote name='Mark Henry' post='2371471' date='Jul... Jul 15 2016, 03:27 PM Mark Henry The most valuable tool for jetting your carbs is a... Jul 14 2016, 04:25 PM JmuRiz I plan on running an O2 sensor in mine too, gives ... Jul 14 2016, 05:43 PM Mark Henry
I plan on running an O2 sensor in mine too, gives... Jul 14 2016, 06:21 PM GeorgeRud I'd imagine a bung for each cylinder would be ... Jul 14 2016, 05:55 PM tornik550 Does anyone know if Weber IDF velocity stacks will... Jul 14 2016, 06:49 PM Mark Henry Measure the ID and the hole spacing center to cent... Jul 14 2016, 06:56 PM Perry Kiehl Clone Mark speaks the truth on the O2 sensor. It makes ... Jul 14 2016, 09:37 PM Mark Henry I have a good O2 meter and I put it on every car I... Jul 15 2016, 12:18 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 28th May 2024 - 07:53 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.