 Brake pedal not returning, Is this the bushing? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Thack |
 Nov 7 2007, 10:10 PM
Post
#1
|
|
Member  Group: Members Posts: 283 Joined: 1-June 05 From: Houston, Tx Member No.: 4,182  |
My brake pedal does not return to the "off" position. I have to pull it back with my hand or shoe. It actually drags the brake pads because I noticed my car not accelerating with the pedal slightly stuck like I pushed it down 3 inches. Is this the bushing? Is this the classic rebuild the cluster with bronze bushings time?
|
   |
 
|
Posts in this topic
Thack Brake pedal not returning Nov 7 2007, 10:10 PM
davep Yes it is. Brake fluid is generally the culprit, c... Nov 7 2007, 10:12 PM ConeDodger Budget for a pedal cluster rebuild, done by severa... Nov 7 2007, 10:17 PM Thack I rebuilt the mc so it must have happened before I... Nov 7 2007, 10:39 PM
ConeDodger
I rebuilt the mc so it must have happened before ... Nov 8 2007, 01:16 AM Cap'n Krusty There's no tension on the springs when the clu... Nov 8 2007, 01:27 AM ConeDodger
As for the rebuilt master cylinder, please don... Nov 8 2007, 11:43 AM geniusanthony You may wanna check that your rubber brake lines h... Nov 8 2007, 03:00 AM Thack Can you drill out this roll pin if it's stuck ... Nov 8 2007, 10:16 AM Cap'n Krusty
Can you drill out this roll pin if it's stuck... Nov 8 2007, 10:54 AM bperry
Can you drill out this roll pin if it's stuc... Nov 9 2007, 12:25 AM Thack So you guys suck it up and buy a $200 master ... Nov 8 2007, 11:59 AM addwestern Rob is spot on in this one. We've rebuilt a fe... Nov 8 2007, 12:01 PM davep Pretty much. $200 does not cover a lot of bod... Nov 8 2007, 12:05 PM Thack Good info. thanks to all of you. Now that I rememb... Nov 8 2007, 12:42 PM davep
Do you guys buy new rotors or have them turned?
... Nov 9 2007, 11:46 AM Jeffs9146
On a scale of 1-10, 10 being the hardest, I woul... Nov 9 2007, 07:45 PM Eric_Shea Guys - The roll pin is "never" a problem... Nov 9 2007, 08:25 PM Eric_Shea One more thing: :D
Good known working master cyl... Nov 9 2007, 08:32 PM Thack
One more thing: :D
Good known working master cy... Nov 9 2007, 09:04 PM Eddie Williams I've gopt one already rebuilt with bronze bush... Nov 9 2007, 11:42 PM Eric_Shea
New brake caliper install. Something about a M/... Nov 10 2007, 12:23 PM Thack Thanks. I'm going to rebuild the cluster and g... Nov 10 2007, 03:15 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 04:34 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.