 1.8 Head cc Question? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| martman |
 May 4 2009, 01:02 PM
Post
#1
|
|
Newbie  Group: Members Posts: 36 Joined: 3-July 04 From: Hemet, CA Member No.: 2,290  |
OK i am building a 2056 with carbs and the 186 webcam. The heads that I am using have been gone thru. I cc the heads to see what the deck height would be and got 44cc. This doesn't seem right to me but not sure. The heads have been rework. So my question is have the heads been decked to much to use in this case.
|
   |
 
|
Posts in this topic
martman 1.8 Head cc Question? May 4 2009, 01:02 PM
type47 I'm not sure I get this. I thought the deck he... May 4 2009, 02:22 PM martman Yes Jim I cc'd the heads and got 44cc on all 4... May 4 2009, 03:50 PM r_towle What are your deck heights with no shims?
Rich May 4 2009, 04:19 PM martman I ran out of time to get the deck height with no s... May 4 2009, 04:38 PM r_towle seems a bit low, take a picture of how you cc... May 4 2009, 04:56 PM martman OK had time to get the deck height, and re cc the ... May 7 2009, 09:05 PM
banger A deck height of .128 sounds a bit high. I am not... May 8 2009, 01:55 AM Todd Enlund Even the .075 deck with no shims or head gaskets i... May 8 2009, 02:09 AM r_towle 96mm bore
71mm stroke
47 cc chamber (head cc and v... May 8 2009, 05:38 AM martman
96mm bore
71mm stroke
47 cc chamber (head cc and ... May 8 2009, 12:27 PM Todd Enlund
So I am close? or not? or just have to start ove... May 8 2009, 01:07 PM jcd914
going with a pair of rebuilt 2.0 heads, or a pair... May 8 2009, 05:17 PM HAM Inc If you're 1.8 chambers are actually 44cc's... May 8 2009, 08:19 AM r_towle man...I wrote a really nice detailed response...th... May 8 2009, 05:00 PM r_towle To fix the piston pin height issue you have two ch... May 8 2009, 05:26 PM martman I dug around and found a stock head from a 1.8, it... May 8 2009, 06:06 PM banger Since you have dished pistons, another option is t... May 8 2009, 09:48 PM martman Here are some pics of the problem head, and troubl... May 9 2009, 12:30 AM HAM Inc The 44cc head is a 1.7. The dirty head is a 1.8.
G... May 9 2009, 08:31 AM HAM Inc
Rich is correct. We spend quite a bit of time pre... May 9 2009, 08:38 AM r_towle
Rich is correct. We spend quite a bit of time pr... May 9 2009, 08:49 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 01:16 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.