 Newly Discovered Hell Hole Cancer |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| kenshapiro2002 |
 Oct 28 2009, 10:43 AM
Post
#21
|
|
Senior Member  Group: Members Posts: 1,441 Joined: 23-July 09 From: Bawlmer, MD Member No.: 10,598 Region Association: MidAtlantic Region  |
Well, the hole itself was repaired, but I was just able to excavate as seen below. Surrounding area is ice pick proof. What are the best "fixes" to be done while keeping the car together? It does not extend into the interior either and the side runners are very solid (had been replaced too).
Attached image(s)  
|
   |
 
|
Posts in this topic
kenshapiro2002 Newly Discovered Hell Hole Cancer Oct 28 2009, 10:43 AM
rjames
Well, the hole itself was repaired, but I was jus... Oct 28 2009, 11:43 AM
Vacca Rabite :agree:
Use your ice pick to see what else may b... Oct 28 2009, 11:45 AM
kenshapiro2002 The hell hole was patched...not with correct sheet... Oct 28 2009, 01:18 PM Sleepin I would check those fuel lines as well. You might ... Oct 28 2009, 11:49 AM URY914
I would check those fuel lines as well. You might... Oct 28 2009, 11:56 AM kenshapiro2002 Redoing fuel lines, pump (relocating to front), fi... Oct 28 2009, 01:20 PM SirAndy
Well, the hole itself was repaired, but ...
I tol... Oct 28 2009, 12:07 PM jasons
Time to drop the engine and do it right! :s... Oct 28 2009, 12:19 PM kenshapiro2002 I do not know how to weld. I guess I'll either... Oct 28 2009, 01:21 PM JazonJJordan 914bonfires bring many tears...
:(
I do not kn... Oct 28 2009, 05:11 PM Racer Chris
I do not know how to weld. I guess I'll eithe... Oct 28 2009, 06:22 PM ghuff
I do not know how to weld. I guess I'll eith... Oct 28 2009, 06:41 PM kenshapiro2002 Guess what I mainly need is the right triangle tha... Oct 28 2009, 01:58 PM SirAndy
Guess what I mainly need is the right triangle th... Oct 28 2009, 02:13 PM kenshapiro2002 That would be #2 in my picture, right? Seems that ... Oct 28 2009, 02:26 PM SirAndy
The PO replaced the longitudinals.
:ttiwwp: Oct 28 2009, 02:30 PM Cevan And use the proper FI clamps on the fuel hose, not... Oct 28 2009, 02:15 PM ghuff Ken, time to start digging in more man..........
... Oct 28 2009, 02:32 PM SirAndy Just to be clear, i'm trying to help you here,... Oct 28 2009, 02:36 PM cal44 Matey.............has that car been down in Davey ... Oct 28 2009, 03:43 PM kenshapiro2002 Really...it's more the flash of the camera...d... Oct 28 2009, 07:09 PM Drums66 I know it's too late,but...you should'nt h... Oct 28 2009, 04:15 PM Vacca Rabite Andy is probably right.
BUT
If you pull the rock... Oct 28 2009, 04:49 PM ghuff
Andy is probably right.
BUT
If you pull the roc... Oct 28 2009, 05:04 PM JazonJJordan (-good man, real good advice from everyone-) Cance... Oct 28 2009, 05:40 PM kenshapiro2002 Any beer you want! :DRUNK:
Andy is probably... Oct 28 2009, 07:18 PM Racer Chris BTW, we have the triangles,made in-house, at a muc... Oct 28 2009, 06:31 PM kenshapiro2002 "Theirs" are $17.25 more but have a... Nov 12 2009, 12:32 PM kenshapiro2002 I'll start digging and poking more tomorrow. I... Oct 28 2009, 07:16 PM ghuff If you pay someone else, take it to a reputable pe... Oct 28 2009, 07:38 PM kenshapiro2002 Already did the CT / MD drive once...why not.
If... Oct 28 2009, 07:58 PM ghuff
Already did the CT / MD drive once...why not.
I... Oct 28 2009, 08:47 PM Racer Chris Your car looks a lot like this one did. Oct 28 2009, 09:36 PM Vacca Rabite Find out where all the H.H. rust is. Clear it. P... Oct 28 2009, 09:37 PM kenshapiro2002 Very sweet offer...thanks.
Find out where all ... Oct 29 2009, 05:32 AM veltror If you think yours was/is bad take a look at mine, Oct 29 2009, 05:10 AM kenshapiro2002 Damn...and doesn't even look like you braced /... Oct 29 2009, 05:35 AM veltror Err yes it was braced and supported.... Oct 29 2009, 10:59 AM kenshapiro2002
Guys...the car is as solid as can be (well..... Oct 29 2009, 11:32 AM SirAndy
Guys...the car is as solid as can be (well...almo... Oct 29 2009, 11:52 AM jasons
Just as i thought ... :sick:
Yeah, the long s... Oct 29 2009, 12:12 PM kenshapiro2002 I assume they were both done. Anyway...even though... Oct 29 2009, 12:25 PM kenshapiro2002 Nah...you thought I was gonna find nothing but can... Oct 29 2009, 12:42 PM SirAndy
Nah...you thought I was gonna find nothing but ca... Oct 29 2009, 12:46 PM rjames
Guys...the car is as solid as can be (well...alm... Oct 29 2009, 02:35 PM kenshapiro2002 Love you, but not that much. :wub:
[quote name=... Oct 29 2009, 02:58 PM rjames
Love you, but not that much. :wub:
[quote name... Oct 29 2009, 05:21 PM jasons Your long does look good. Why did you say that on... Oct 29 2009, 11:46 AM Racer Chris Pic 2 looks like there was a repair at the rear of... Oct 29 2009, 12:01 PM kenshapiro2002 Probably the "soft" area I showed in my ... Oct 29 2009, 12:40 PM Racer Chris Sir Andy beat me to it. :) Oct 29 2009, 12:02 PM Racer Chris Keep digging Ken! Oct 29 2009, 12:05 PM jasons I don't know. The outter long looks original ... Oct 29 2009, 12:36 PM FourBlades This thread is making me nostalgic about fixing ru... Oct 29 2009, 12:51 PM kenshapiro2002 Same with these other guys. Otherwise somebody wou... Oct 29 2009, 12:55 PM kenshapiro2002 I know...don't even love you enough to undo th... Oct 29 2009, 06:56 PM kenshapiro2002 Guess you guys were right. The seats were out so I... Oct 29 2009, 06:59 PM neil30076
Guess you guys were right. The seats were out so ... Oct 29 2009, 07:09 PM kenshapiro2002 Nah...the car is wonderful...just wanted to see wh... Oct 29 2009, 07:15 PM neil30076
Nah...the car is wonderful...just wanted to see w... Oct 29 2009, 07:23 PM Racer Chris
Guess you guys were right. The seats were out so ... Oct 29 2009, 08:55 PM kenshapiro2002 Wasn't trying to fool you...was being entertai... Oct 29 2009, 09:03 PM Racer Chris
So is your family. :lol4:
You know my family? ... Oct 30 2009, 10:08 AM kenshapiro2002 No, but you're so "nice*", I'm b... Oct 30 2009, 12:57 PM kenshapiro2002 Maybe you're not a "Super Genius". T... Oct 29 2009, 09:08 PM SirAndy
I want a valuable car!!!
I have one ... Oct 29 2009, 09:15 PM kenshapiro2002 No...you have a car that could be valuable one day... Oct 29 2009, 09:18 PM SirAndy
I have an ex wife like that.
Me too. I gave both... Oct 29 2009, 09:30 PM kenshapiro2002 Actually have two of them myself. With the first o... Oct 30 2009, 05:29 AM kenshapiro2002 Did seem kinda dry in here when I first showed up.... Oct 29 2009, 07:25 PM neil30076
Did seem kinda dry in here when I first showed up... Oct 29 2009, 07:39 PM kenshapiro2002 Love 928s...one of the best things Porsche ever di... Oct 29 2009, 07:45 PM kenshapiro2002 "Not that special"? You're nutz. :sc... Oct 29 2009, 09:16 PM bandjoey Heck...It's a beautiful car. Do what all non ... Oct 29 2009, 09:21 PM kenshapiro2002 Update....I started clearing out the rust to where... Nov 12 2009, 12:26 PM SirAndy
Then I need somebody to weld in a triangle with t... Nov 12 2009, 01:25 PM kenshapiro2002 Hmmmmm...on the Tangerine Racing site, they call t... Nov 12 2009, 01:47 PM Spoke About the triangles, are they structural or protec... Nov 12 2009, 01:56 PM SirAndy
About the triangles, are they structural or prote... Nov 12 2009, 02:07 PM kenshapiro2002 So, they were used to support the weight of the ca... Nov 12 2009, 02:15 PM SirAndy
So, they were used to support the weight of the c... Nov 12 2009, 02:47 PM kenshapiro2002 Already been doing that and the right rear one is ... Nov 12 2009, 03:35 PM SirAndy
How do you feel about the pieces folks sell that... Nov 12 2009, 05:32 PM crash914 Ken, you can always swing by and see the triangles... Nov 12 2009, 05:57 PM kenshapiro2002 Herb...I really appreciate that, but me using your... Nov 12 2009, 07:17 PM kenshapiro2002 What do think would be a reasonable range of fee f... Nov 13 2009, 09:03 AM kenshapiro2002 Oh man...bought a 4 1/2" Ryobi Angle Grinder.... Nov 13 2009, 11:42 AM kenshapiro2002 Got one (AA was down to only 180 in stock). On the... Nov 13 2009, 11:49 AM SirAndy
Got one (AA was down to only 180 in stock). On th... Nov 13 2009, 12:34 PM Vacca Rabite I am usually off the Friday after Turkey Day.
IF... Nov 13 2009, 06:32 PM kenshapiro2002 If I can wait that long, I'll let you know...w... Nov 13 2009, 06:45 PM OU8AVW Keep me posted you guys. I would be hip to getting... Nov 13 2009, 06:59 PM Racer Chris I'm sure glad you found one in stock at AA wit... Nov 13 2009, 09:03 PM kenshapiro2002
I'm sure glad you found one in stock at AA wi... Nov 13 2009, 09:50 PM kenshapiro2002 I concur. I've been jacking using either the t... Nov 13 2009, 09:51 PM SirAndy
I concur. I've been jacking using either the ... Nov 13 2009, 09:56 PM kenshapiro2002 Mine has been converted to a side shifter, so I... Nov 13 2009, 10:44 PM kenshapiro2002 Well...almost ready for welding. The section label... Nov 17 2009, 11:25 AM strawman Hi Ken,
I'm not sure that I agree that the tr... Nov 18 2009, 01:04 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 11:48 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.