 transmission leaking..., dripping from clutch fork and bell housing... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| malaga_red75 |
 Aug 7 2010, 04:28 PM
Post
#1
|
|
'74 2.5L N/A Subie  Group: Members Posts: 454 Joined: 5-March 06 From: Menlo Park, CA Member No.: 5,674 Region Association: None  |
title says it. just got my car back on the road and it now has a transmission leak. dripping from the clutch fork and bell housing... let me know what you think.
-Peter |
   |
 
|
Posts in this topic
malaga_red75 transmission leaking... Aug 7 2010, 04:28 PM
Dr Evil There are two sources of leaking in that area, the... Aug 7 2010, 04:34 PM avidfanjpl Rear main seal. You do not have to drop the engine... Aug 7 2010, 04:38 PM
Drums66
Rear main seal.
John
did you use synthetic be... Aug 8 2010, 02:23 PM underthetire Yep, mine leaked from the trans input shaft seal. ... Aug 7 2010, 04:44 PM davep Since there are two possible sources for the leak ... Aug 7 2010, 07:16 PM Dr Evil Well, my advice was based on it actually being rul... Aug 7 2010, 07:26 PM avidfanjpl Dr. Evil is right. Only one way to know. Yank that... Aug 7 2010, 07:42 PM malaga_red75 lucky for me, i was already planning on pulling th... Aug 7 2010, 08:20 PM Bleyseng Does this setup have support for the input shaft? ... Aug 8 2010, 04:36 AM malaga_red75
Does this setup have support for the input shaft?... Aug 8 2010, 11:54 AM Bleyseng on type 4 cranks inside the end is a needle beadin... Aug 8 2010, 12:13 PM malaga_red75 well, i spent the first half of the day building a... Aug 8 2010, 06:33 PM malaga_red75 tranny... Aug 8 2010, 06:34 PM Dr Evil Take out the socket head that holds the fork in an... Aug 8 2010, 06:45 PM malaga_red75 i removed the fork and the TOB. do i need to remo... Aug 8 2010, 06:58 PM malaga_red75 just pulled the TOB sleeve... you're right, it... Aug 8 2010, 07:07 PM malaga_red75 nuther...
now, is there a trick to replacing the... Aug 8 2010, 07:08 PM Dr Evil Seal puller, and then install a new one. Cheap, an... Aug 8 2010, 08:10 PM underthetire You must be young and full of piss and vinegar. Th... Aug 8 2010, 08:57 PM malaga_red75
You must be young and full of piss and vinegar. T... Aug 8 2010, 10:18 PM Richard Casto You can get a seal puller from just about anywhere... Aug 9 2010, 06:21 AM malaga_red75
When reading this thread, I also am curious to k... Aug 9 2010, 10:31 AM underthetire
When reading this thread, I also am curious to ... Aug 9 2010, 12:25 PM malaga_red75 just checked... there is a sleeve-style bearing ju... Aug 9 2010, 12:51 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 18th May 2024 - 06:28 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.