2.7L, So why is 2.7L the motor to avoid? Options

[Mark Henry]

There is a mod to make the hydraulic tensioner failsafe. The other issue is they can leak.
The 993 studs are getting spendy, so I'd use Supertec studs.
Many of the 2.7 used alusil cylinders, they can be reconditioned but your stuck with stock pistons, unless you replate them with nicasil.
A 2.7 that had reactors will also have worn out guides.

Done right they are a good engine, I have a 2.7 core with casesavers and steel studs if anyone is looking. I'm going 3.0.

The Cap'n's dream engine would be nice, but that Al case and squirter machine work needed will set you back $3k alone.

[seebobgo]

If someone is going to start looking for a 6 to build what do you want

3.6 (IMG:style_emoticons/default/biggrin.gif)

(IMG:style_emoticons/default/agree.gif) go for the best

[Steve]

I installed a 1974 2.7 out of a U.S. 911S Carrerra back in 1986. With Webers it was the best sounding engine I have ever heard. I used go back and forth through the Alameda tunnel just to listen to the engine. I also used a stock 911 2.0 flywheel and clutch. The engine matched the stock 914 gearing quite well and was a blast to drive. Then in 2000 it started pulling head studs and lost most of its power. At the time my choice was to spend $6k to overhaul it or buy something else. I ended up buying a used 1984 Euro 3.2 motor for $5200. I miss the sound of the webers, but the driveability and reliability of the motronic fuel injection is amazing. The down side now is that 1st gear is to low for the 3.2 motor and most of the time I now start off in second. I only use 1st when starting from stop on a hill. If the 2.7 motor has been overhauled properly to address the issues and the price was right, then I would recommend it highly.

[Cap'n Krusty]

Well, Cap, remind me to not have you build a 2.7L.
My home built has been running fine or 10 years...with a rebuild at 7 years of age.
Both the *993 Divilars* and the Carrera tens have worked flawlessly.

Here's the latest chassis dyno sheet.....but hay, I'm just an amateur with no preconceived notions.

Well, JP, I just reread what I wrote. I don't believe I said anything about a 2.7 being bad, or not living as long as anything else. I pointed out that they pull studs unless they're inserted, and the SC broken stud problem is at least as bad, or even worse. I then said I'd prefer a short stroke 2.5. Not that it's necessarily any better, but it does have a certain coolness factor. As for the comment from Mark regarding the cost of the cases, I have 4, so it really doesn't matter all that much to me. I can always sell one to pay for the mods, which aren't as expensive for me as they seem to be for him. In the time since you built that motor with the 993 Dilivar studs, most experienced 911 machinists and engine builders will tell you they've followed Porsche's service literature and gone to steel studs. What can I say? I also didn't say oil fed tensioners were bad, or that they failed more than the old style, just that I'd spend the money elsewhere. And it's a LOT of money, relative to the price for 2 kits.

The Cap'n

[bandjoey]

If anyone has one of those old stud pulling nasty nobody wants one motors in the garage they just can't live with, I'll send my shipping address and take it off your hands. Don't want anyone to worry about a motor they just can't stand. (IMG:style_emoticons/default/poke.gif) (IMG:style_emoticons/default/lol-2.gif)

[Dr Evil]

Here is what I learned when I rebuilt my 74 2.7:

1) As stated, alusil can be reconditioned for cheap. I paid $192 to have all 6 cylinders done at Motorworks in San Diego, CA. That saved me a few grand on new ones as urban legend stated you can not do such a thing. Complete, expensive, unfounded, bull shit. The pistons are not coated in nickasil, they are ferrite coated or some such thing. They will be fine.

2) The 74 is the best starting point as that year did not have the thermal reactors.

3) I was lucky, my case had case savers installed. This is a necessity.

4) You DO NOT need an oil cooler for a 2.7. It is dependent on several things. I kept the stock CIS and CR and my engine had fine oil temps.

5) Oil fed tensioners are not mandatory at all. As Krusty said, use the mechanical ones with locks and be money ahead and have one less failure point in your lube system. I have always felt the oil pressure fed ones to be over engineered and unnecessary.

6) The 74 2.7 had a very peaked tq curve in the low band and then fell on its face. As previously mentioned, a set of SC cams, which I got reground for $200, make the curve a nice flat climb that was a real joy to drive.

7) Divilar is crap. It tends to crack and this is a known failure point. Any moisture gets onto the studs and it begins the degradation process. This is a widely known, and proven point. It is even mentioned in the 911 engine rebuild book published by the guy form Pelican (just one easy place to find it, he is not a guru). I forget what I used, but it was proven to be superior in tests. I needed results I could see rather than hand-me-down knowledge from people.

[campbellcj]

I love my 2.7. It darn near scared the shit out of me on a quick test drive this evening. In a good way...

(IMG:http://www.914world.com/bbs2/uploads_offsite/farm3.static.flickr.com-21-1283055700.1.jpg)
Porsche 2.7 twin-plug engine by cjcam, on Flickr

[carr914]

JP, as Cap & Dr Evil said, Divilars are not the recommended way to go as they once were. My builder (probably 5 motors a week) only uses Porsche Steel Studs now. This has changed in just the last couple of years. In the original estimate he gave me on my 2.7, he stated Divilar, but when he built he used Porsche Steel. My 2.5 ( built on a 7R case) I'm sure had Divilar.

Picture Porn ( my 2.7 that is For Sale (IMG:style_emoticons/default/first.gif) )

[carr914]

The 2.5 Twin-Plug on the Dyno. The numbers off the Top of my Head were 218 HP & near 190 Ft/Lbs Torque

[J P Stein]

The stud issue will never be settled here. Suffice it to say that my gurus build with nothing but Divilar( for aluminum cylinders)....that would be Steve Wiener & Rothsport. Henry at Supertech had his designed & produced studs from some kind of stainless with an expansion coefficient similar to Aluminum...not Divilar but similar and he's no slouch. They are sold at a decent price, right Mark?
The Pelican 911 engine building forum has been going around & around about this for years and prolly will for the foreseeable future. Pick your own guru and HIS opinion, but don't tell me mine has no clue.

The 76-77 2.7L has the improved (larger scavenge side) oil pump plus the oiling mod, Doc.....that cost a pretty penny to have done. I would use one of those cases if you can find a straight one. Alusil cylinders reconditioned to size?

I would never use collars on tensioners. If the tensioner fails you don't have any warning like you do with a slowly failing oil fed ten. The collar starts getting hammered on, breaks and the chain goes slack. At best you'll then go buy a bunch of valves. Pick your poison.

[pete-stevers]

The 993 Divilar, full thread, coated studs are the way to go. Steel studs come loose due to uneven expansion rates......no big deal if you don't mind retorquing the heads a few times till the aluminum is done coldworking (if you don't know what type of coldworking I'm speaking of, ask)......this assumes case savers have been installed.

The 2.7L gets a bad rap. All the motors have weak points and need to be rebuilt to adress these issues. With a mag case just keep it cool and it'll live. That said, if I was gonna do it again I'd use a 3.0L unless I was building to class.

Glad i finally got you to see the light!! (IMG:style_emoticons/default/wink.gif)
But the down side with a cis 3.0 is fittment if you plan to keep the cis intact
I dropped my entire drive train an inch to accomodate with no cutting of body, requiring a modified shift rod on the underside
where as the 3.2 just requires a turn of the intake to fit
while i love my early 3.0
i think i would go 3.2 with motronic if i am going to do it agian

[Mark Henry]

The stud issue will never be settled here. Suffice it to say that my gurus build with nothing but Divilar( for aluminum cylinders)....that would be Steve Wiener & Rothsport. Henry at Supertech had his designed & produced studs from some kind of stainless with an expansion coefficient similar to Aluminum...not Divilar but similar and he's no slouch. They are sold at a decent price, right Mark?
The Pelican 911 engine building forum has been going around & around about this for years and prolly will for the foreseeable future. Pick your own guru and HIS opinion, but don't tell me mine has no clue.

The 76-77 2.7L has the improved (larger scavenge side) oil pump plus the oiling mod, Doc.....that cost a pretty penny to have done. I would use one of those cases if you can find a straight one. Alusil cylinders reconditioned to size?

I would never use collars on tensioners. If the tensioner fails you don't have any warning like you do with a slowly failing oil fed ten. The collar starts getting hammered on, breaks and the chain goes slack. At best you'll then go buy a bunch of valves. Pick your poison.

The Supertec studs are about $600. If you decided to go twin plug you'll have a hard time getting past the stock barrel nuts.
If you take apart the hydraulic tensioner you can make a spacer out of tubing, but you lose the circlip. Doesn't matter once the tensioner is installed and then it's bulletproof.

Saying you have 4 Al cases is an apples to oranges argument. On the bird board classifieds they have an asking price of $2k and then you need squirters and the oiling mod.
My 3.0 had no broken studs, but I'll be replacing them anyways.

[JmuRiz]

Only a couple of people have used 2.7 or 3.0 with CIS...has anyone done a 2.7 or 3.0 with a Bitz EFI conversion? Wondering if that'd run cooler. Just thinking out loud.

[Mark Henry]

Only a couple of people have used 2.7 or 3.0 with CIS...has anyone done a 2.7 or 3.0 with a Bitz EFI conversion? Wondering if that'd run cooler. Just thinking out loud.

I'm pretty sure that it's a megasquirt system with all the needed bits and pre-programed with the maps.
That's why the price is so good.
IIRC a member here used it on his 911, try a search.

[SLITS]

Only a couple of people have used 2.7 or 3.0 with CIS...has anyone done a 2.7 or 3.0 with a Bitz EFI conversion? Wondering if that'd run cooler. Just thinking out loud.

If the A/F ratio is correct, what the hell would make the engine run cooler over a CIS setup? I've done two CIS setups myself and will do a third soon.

[jfort]

[That said, if I were building a performance motor for my car, I'd build a 2.5 based on a 2.0 S crank and an aluminum case, with ported big valve heads. The machinists I use say they can get me right about 200 HP from a street drivable 2.2, so a short stroke 2.5 should be a revvin'n fool, and have even better HP.]

Agree. I have a 2.5 built on a 2.0. I believe it is an E cam. Love it.

[Cap'n Krusty]

[quote name='Mark Henry' date='Aug 29 2010, 12:46 PM' post='1363069']



I would never use collars on tensioners. If the tensioner fails you don't have any warning like you do with a slowly failing oil fed ten. The collar starts getting hammered on, breaks and the chain goes slack. At best you'll then go buy a bunch of valves. Pick your poison.
[/quote]



Saying you have 4 Al cases is an apples to oranges argument. On the bird board classifieds they have an asking price of $2k and then you need squirters and the oiling mod.
My 3.0 had no broken studs, but I'll be replacing them anyways.
[/quote]

I've been using collars for 30+ years, and 912 valve spring retainers before that, and I've never had a chain related failure on any engine on which they've been used. Ever.

As for the "asking price" for those cases, I had ads all over the place for both plain cases and core long blocks, at a price lower than that, and I don't think I got more than 2 or 3 replies during the several months I was actively trying to sell them. I finally decided to hold onto the stuff.

The Cap'n