 Copper nuts, exhaust leaks! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| mgphoto |
 Sep 16 2010, 09:06 PM
Post
#1
|
|
"If there is a mistake it will find me"  Group: Members Posts: 1,339 Joined: 1-April 09 From: Los Angeles, CA Member No.: 10,225 Region Association: Southern California  |
Hello,
I am having a problem with exhaust leaks, I am, for the first time using copper nuts as opposed to the steel with insert and flange Porsche part # 039.256.297 see photo below.  I would still be using these if I hadn't lost one, and Porsche says these are NLA. The procedure I would use, after replacing the copper seals, I would use Never Seez on the studs and torque the steel nuts to 16 ft-lbs. I am not sure if I should use Never Seez with the copper nuts and I am not sure the torque is correct for these fasteners, as they are oval shaped and seem tighter to start with? Any experience with this would be very helpful. Thanks, Mike |
   |
 
|
Posts in this topic
mgphoto Copper nuts Sep 16 2010, 09:06 PM
brer I believe the Porsche nuts are copper plated, not ... Sep 16 2010, 09:32 PM
Drums66
I believe the Porsche nuts are copper plated, not... Sep 17 2010, 11:11 AM SGB Copper is used so it can be cold chiseled off if t... Sep 16 2010, 10:35 PM mgphoto
Copper is used so it can be cold chiseled off if ... Sep 17 2010, 12:37 AM avidfanjpl Hey I used gasket cement, but superglue is good to... Sep 17 2010, 01:22 AM Van Copper coated. You can get them from NAPA for abo... Sep 17 2010, 05:25 AM realred914 i'd still go with the specified torque as poin... Sep 17 2010, 10:49 AM mgphoto
i'd still go with the specified torque as poi... Sep 17 2010, 01:02 PM Cap'n Krusty I agree with Dave (realred). It would be well for... Sep 17 2010, 02:17 PM mgphoto
I agree with Dave (realred). It would be well fo... Sep 17 2010, 04:59 PM Cap'n Krusty
I agree with Dave (realred). It would be well f... Sep 18 2010, 07:58 AM mgphoto
[quote name='mgphoto' post='1372291' date='Sep 17... Sep 18 2010, 09:41 AM mgphoto
[quote name='mgphoto' post='1372291' date='Sep 1... Sep 18 2010, 12:30 PM mgphoto
[quote name='mgphoto' post='1372503' date='Sep 18... Sep 18 2010, 04:40 PM brer
[quote name='mgphoto' post='1372503' date='Sep 1... Sep 18 2010, 06:58 PM Cap'n Krusty
[quote name='mgphoto' post='1372291' date='Sep 1... Sep 18 2010, 07:40 PM charliew Nickel antisieze is for high temperature. Solid br... Sep 17 2010, 05:08 PM Krieger Didn't someone reccomend heating the copper ga... Sep 17 2010, 07:58 PM dangrouche yes by all means, flame the new copper gaskets til... Sep 17 2010, 08:42 PM solex I had it with the copper plated nuts, and pulling ... Sep 18 2010, 11:14 AM mgphoto I got it to work by using a 10mm x 1.25 helicoil a... Sep 20 2010, 10:39 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th May 2024 - 11:02 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.