 small bore, high revving 6, anyone running one now? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| DanT |
 Dec 18 2010, 10:12 AM
Post
#1
|
|
Going back to the Dark Side!  Group: Members Posts: 4,300 Joined: 4-October 04 From: Auburn, CA Member No.: 2,880 Region Association: None  |
I have the chance to acquire an 2.0L 6 case and have thought about building a small bore 2.0-2.5L high revving 6.
Anyone out there running such a combination right now? This would be a street/AX motor. Prefer to do single plug. Most likely use Webers, since MFI parts are getting hard to come by . What combinations of Pistons/cams are you folks using? Pictures of motor builds would be appreciated. Just sliding in a 2.7L CSI motor is also a consideration if the small bore motor becomes too much of a pain. (IMG:style_emoticons/default/biggrin.gif) |
   |
 
|
Posts in this topic
DanT small bore, high revving 6 Dec 18 2010, 10:12 AM
jjackson
I have the chance to acquire an 2.0L 6 case and h... Dec 18 2010, 10:31 AM messix are you sure you want small bore?
a small bore wi... Dec 18 2010, 10:59 AM ME733 The ..2.0 six...had a short stroke...66mm.(same as... Dec 18 2010, 11:23 AM campbellcj IMO you would not want a peaky small six for stree... Dec 18 2010, 11:39 AM campbellcj IMO you would not want a peaky small six for stree... Dec 18 2010, 11:39 AM J P Stein My old 2.7L would pull 7300 with all Porsche parts... Dec 18 2010, 11:49 AM sww914 They say the last 800 to get to 8000 will cost you... Dec 18 2010, 12:57 PM brant I put 100 racing hours onto a 2.0/6 with an alumin... Dec 18 2010, 03:23 PM GeorgeRud The 66mm crank with the 90 mm piston bore does mak... Dec 18 2010, 03:41 PM Mark Henry If you're rebuilding all sixes work out about ... Dec 18 2010, 05:20 PM MikeSpraggi Haven't driven it yet, but I've had a 2.2L... Dec 18 2010, 05:51 PM d914 I had a 2.5 liter short stroke six... loved it for... Dec 18 2010, 05:59 PM Cap'n Krusty Ahem! I have an aluminum case, a long block, ... Dec 18 2010, 07:54 PM
J P Stein
Ahem! I have an aluminum case, a long block,... Dec 18 2010, 08:23 PM jfort Have a 2.5 short striker with E cam and short gear... Dec 19 2010, 07:35 PM Mark Henry There's a set undersize rod bearings on the bi... Dec 19 2010, 08:17 PM koozy :shades2: Hmmmmmm..... Whatcha doooooin??? :idea: Dec 19 2010, 08:41 PM Eric_Shea I have Greg's 2.5 now. It will be twin plugge... Dec 19 2010, 09:56 PM DanT Mike,
I have always wanted to try a high revving 6... Dec 19 2010, 10:22 PM koozy I should have saved the 2, 2.4 engines I had. The ... Dec 19 2010, 11:45 PM turboman808 Have a 2.7 with some work that revs to 8000 rpm. ... Dec 20 2010, 12:00 AM Michael N Dan,
Since you are so close to my house you are w... Dec 20 2010, 01:38 PM Michael N ... Dec 20 2010, 01:45 PM ONTHEGRIND Michael if he doesn't I will lol I am also in ... Dec 20 2010, 03:21 PM DanT Thanks Michael....
over the years of instructing a... Dec 20 2010, 05:13 PM campbellcj For years I dreamed/planned to build (er, have som... Dec 20 2010, 05:18 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th May 2024 - 03:17 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.