 winsheild removal, rusty cowl, black rubber and Frit |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| sean_v8_914 |
 Apr 19 2011, 07:18 AM
Post
#1
|
|
Chingon 601  Group: Members Posts: 4,011 Joined: 1-February 05 From: San Diego Member No.: 3,541  |
this project has a major case of the " while youre in there" syndrome. this started as a cowl rust repair and chrome delete.
Peter's chrome trim is in great shape. it is RARE to find 914 window trim that fits flush. it is soft AL and the shape is critical to a snug fit after removign the wipers, we have to locate 20 plastic trim clips Attached thumbnail(s) 
|
   |
 
|
Posts in this topic
sean_v8_914 winsheild removal, rusty cowl Apr 19 2011, 07:18 AM
sean_v8_914 I marked their position with blue tape. you can fe... Apr 19 2011, 07:22 AM sean_v8_914 the 20 trim clips are little plastic things held i... Apr 19 2011, 07:28 AM sean_v8_914 the single edge is thinner and great for locating ... Apr 19 2011, 07:34 AM sean_v8_914 slow and easy taps Apr 19 2011, 07:35 AM sean_v8_914 clip locations near blue tape Apr 19 2011, 07:36 AM sean_v8_914 this one was too tight for the utility blade so i ... Apr 19 2011, 07:39 AM sean_v8_914 dftj Apr 19 2011, 07:40 AM sean_v8_914 this lower corner has dirt and debris in teh crack... Apr 19 2011, 07:43 AM sean_v8_914 side clip locations Apr 19 2011, 07:45 AM sean_v8_914 bottom clip locations Apr 19 2011, 07:46 AM sean_v8_914 clip close up.
here you can see the size and shape... Apr 19 2011, 07:48 AM sean_v8_914 the trim frame should coe out in one pc. if you ge... Apr 19 2011, 07:50 AM sean_v8_914 typical to many 914s is the rust in teh windsheild... Apr 19 2011, 07:54 AM sean_v8_914 I found a pic of where the clip pin engages teh wi... Apr 19 2011, 07:56 AM sean_v8_914 they all have rust in them Apr 19 2011, 07:56 AM sean_v8_914 I guess you could remove the window with the inter... Apr 19 2011, 08:03 AM sean_v8_914 im so retarded...more coffee please
admins: please... Apr 19 2011, 08:12 AM okieflyr This is very relevant to what I want to do. I have... Apr 19 2011, 10:21 AM silver74insocal :popcorn: cool thread Sean. keep posting them pics... Apr 19 2011, 10:47 AM sean_v8_914 I used to tie a guitar string onto two pc of broom... Apr 19 2011, 11:26 PM sean_v8_914 here is a pic of the trim hilding clip. you only n... Apr 19 2011, 11:28 PM sean_v8_914 A pillar clip locations Apr 19 2011, 11:29 PM sean_v8_914 bottom trim clip locations Apr 19 2011, 11:30 PM sean_v8_914 trim should just fall out in one pc still connecte... Apr 19 2011, 11:32 PM sean_v8_914 here is how that window cutting out tool works. y... Apr 19 2011, 11:35 PM sean_v8_914 do not nick the glss or try to pull teh window out... Apr 19 2011, 11:37 PM sean_v8_914 wire wheel...went a little crazy.I pick away at te... Apr 19 2011, 11:58 PM sean_v8_914 for some reason teh photos make it all look so cle... Apr 20 2011, 12:01 AM sean_v8_914 tape lines and over spray are so skanky. there are... Apr 20 2011, 12:06 AM sean_v8_914 POR 15 is only on the rough metal. I did use it he... Apr 20 2011, 12:11 AM sean_v8_914 get under these corners with a mirror and teh abov... Apr 20 2011, 12:12 AM sean_v8_914 under teh seal trough rust
little rust incubator.... Apr 20 2011, 12:15 AM sean_v8_914 reg Apr 20 2011, 12:16 AM sean_v8_914 the seal from dash to window was petrified. 914rub... Apr 20 2011, 12:23 AM sean_v8_914 these 2 plastic dash nuts are a bitch. a short 13m... Apr 20 2011, 12:24 AM sean_v8_914 sand teh POR 15 with some 220.
then I use Wurth or... Apr 20 2011, 12:27 AM sean_v8_914 sand etching primer with 220 then I coat with 2 pa... Apr 20 2011, 12:35 AM Rusty Sean, this is GREAT info!! :beer2: Apr 20 2011, 06:51 AM sean_v8_914 sand epoxy smoooooth with 320. stay away from edge... Jun 10 2011, 08:41 AM sean_v8_914 the black rubber window trim that replaces teh chr... Jun 10 2011, 08:50 AM sean_v8_914 I was going to set the window by myself when a fre... Jun 10 2011, 09:07 AM sean_v8_914 should I do a seperate post for the back wimdow? t... Jun 10 2011, 09:12 AM sean_v8_914 e brake still works...a miracle at best Jun 10 2011, 09:14 AM sean_v8_914 OK. i didnt want to leave anyone with that horrid ... Jun 10 2011, 09:17 AM
saigon71
OK. i didnt want to leave anyone with that horrid... Jun 10 2011, 04:30 PM rick 918-S Nice work Sean! There are many guys here that ... Jun 11 2011, 07:54 AM sean_v8_914 thankyou for the kind words. I have learned so muc... Jun 11 2011, 11:20 AM sean_v8_914 ta da! the end Jun 13 2011, 12:02 AM sean_v8_914 shhhh Jun 13 2011, 12:08 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 18th May 2024 - 06:26 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.