 removing rear hub, just like the pelican article |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| d914 |
 May 23 2004, 07:11 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,331 Joined: 12-July 03 From: Atlanta, ga Member No.: 904 Region Association: South East States  |
Re-doing the back axles, putting on longer studs on, rr rear bearings, new cvs etc.... The one side comes out like a dream, the other frigging GD piss poor exused for a hub will not move..
Back to the article, just like theirs,,,,,,,,,,,,now trying to take out the bearing carrier,,,,,,,,,, after two trips to home depot and lowes and NEITHER carries a offset wrench,,,,,,,,, Back to Harbor freight tomorrow. (,,,,,,,,,) fill in normal New jersey adjectives bright side I picked up my 46 webers and some misc pieces from a buddy today. Whole car ready for re assembly after I get this god damn flange offffffff... |
   |
 
|
Posts in this topic
d914 removing rear hub May 23 2004, 07:11 PM
Brad Roberts Two words:
Air Chisel.
Takes 10 seconds to pop o... May 23 2004, 07:14 PM d914 three words
don't have one
do have a baby s... May 23 2004, 07:32 PM d914 tools of violence May 23 2004, 07:44 PM d914 inside hub, sorry new camera May 23 2004, 07:45 PM d914 outside May 23 2004, 07:46 PM d914 the garage May 23 2004, 07:54 PM d914 one more time May 23 2004, 07:54 PM d914 I seen some discussions on the make of bearings..
... May 24 2004, 10:24 AM thesey914 Use heat penetrating oil and keep pounding :smash:... May 24 2004, 10:53 AM airsix Drill some holes in a piece of plate so you can at... May 24 2004, 12:25 PM Eric_Shea Beat the Fuch out of it. :smash: May 24 2004, 01:26 PM MattR I tried all sunday to get my hubs out for a 5 lug ... May 24 2004, 03:39 PM Bigbohr Haven't tried the airchisel option, but a big ... May 24 2004, 03:55 PM lapuwali QUOTE
d914 Airsix your a Genius.
used a spacer turned backwa... May 24 2004, 04:21 PM MattR Oh, you're right. I'll try heat again. I... May 24 2004, 04:31 PM airsix cgnj Hi,
Went through the same thing when I did my 5 lu... May 24 2004, 05:31 PM airsix d914 ok back to the bearings....will the skf's work... May 24 2004, 06:48 PM d914 she rolls again... The rear bearings are in along ... Jul 11 2004, 03:03 PM watsonrx13 OK, now that the bearings are in, which ones did y... Jul 11 2004, 07:37 PM
d914 sucked it up returned the ones I had and proudly a... Jul 11 2004, 07:54 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 28th May 2024 - 10:02 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.