 Rubber grommet for 914/6 starter wire? Part #? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| TorqueJunkie |
 Jun 19 2011, 08:34 PM
Post
#1
|
|
Newbie  Group: Members Posts: 48 Joined: 25-May 10 From: Baltimore, MD Member No.: 11,760 Region Association: None  |
I am looking for the part number for the rubber grommet that goes into the factory sheet metal hole (about 1.5 inch hole or so) That the starter cable goes through. Looked in factory diagrams but cant find it. Anyone know what part # it is?
(IMG:http://www.914world.com/bbs2/uploads_offsite/i88.photobucket.com-11760-1308537298.1.jpg) |
   |
 
|
  |
Replies(1 - 9)
| tomeric914 |
Jun 20 2011, 07:07 AM
Post
#2
|
|
One Lap of America in a 914! Group: Members Posts: 1,259 Joined: 25-May 08 From: Syracuse, NY Member No.: 9,101 Region Association: North East States 
|
I used a
|
|
|
|
| TorqueJunkie |
Jun 20 2011, 08:05 AM
Post
#3
|
|
Newbie Group: Members Posts: 48 Joined: 25-May 10 From: Baltimore, MD Member No.: 11,760 Region Association: None |
QUOTE(tomeric914 @ Jun 20 2011, 09:07 AM)  I used a Ford valve cover breather grommet available in the HELP! section of my FLAPS. Perfect fit. ok will go to autozone and see if they have anything like that there in the section. Thanks. Anyone have the factory number just in case? |
|
|
|
| Bee Jay |
Jun 20 2011, 10:23 AM
Post
#4
|
|
Member Group: Members Posts: 204 Joined: 22-April 05 From: Lompoc, Ca. Member No.: 3,964 |
Isn't that hole for the throttle linkage/rod thingie?
Bee Jay My bad, the throttle hole is on the other side. Bee Jay |
|
|
|
| tomeric914 |
Jun 20 2011, 11:33 AM
Post
#5
|
|
One Lap of America in a 914! Group: Members Posts: 1,259 Joined: 25-May 08 From: Syracuse, NY Member No.: 9,101 Region Association: North East States
|
QUOTE(TorqueJunkie @ Jun 20 2011, 10:05 AM) ok will go to autozone and see if they have anything like that there in the section. Thanks. Anyone have the factory number just in case? If you don't find it or can wait, drop me a PM and I'll get the part number off the extra one I have. |
|
|
|
| Cap'n Krusty |
Jun 20 2011, 11:46 AM
Post
#6
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
It's probably sold with the harness, and may not be available separately.
The Cap'n |
|
|
|
| Eric_Shea |
Jun 20 2011, 02:18 PM
Post
#7
|
|
PMB Performance Group: Admin Posts: 19,275 Joined: 3-September 03 From: Salt Lake City, UT Member No.: 1,110 Region Association: Rocky Mountains  |
QUOTE drop me a PM and I'll get the part number off the extra one I have Put the part # here so all can benifit. |
|
|
|
| TorqueJunkie |
Jun 20 2011, 07:15 PM
Post
#8
|
|
Newbie Group: Members Posts: 48 Joined: 25-May 10 From: Baltimore, MD Member No.: 11,760 Region Association: None |
QUOTE(Eric_Shea @ Jun 20 2011, 04:18 PM) QUOTE drop me a PM and I'll get the part number off the extra one I have Put the part # here so all can benifit. Yes, could you please post the number...I might be sold with harness, but would like to check. Still looking... Thanks |
|
|
|
| tomeric914 |
Jun 20 2011, 07:32 PM
Post
#9
|
|
One Lap of America in a 914! Group: Members Posts: 1,259 Joined: 25-May 08 From: Syracuse, NY Member No.: 9,101 Region Association: North East States
|
HELP! part number 42344
It was a Chrysler PCV grommet. Available pretty much anywhere. http://www.autozone.com/autozone/parts/Mot...ier=102885_0_0_ |
|
|
|
| bdstone914 |
Jun 20 2011, 08:30 PM
Post
#10
|
|
bdstone914 Group: Members Posts: 4,522 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
Starter wire is part of the standard 914/6 harness correct? Ill look at the original 6 harness I have and see if it has it.
|
 |
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th May 2024 - 08:33 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.