Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> GREAT REPAIR SYSTEM FOR DASH COVER!, Low-cost and easy repair for all the cracks
stewteral
post Jun 22 2011, 12:50 PM
Post #1


Old Member
**

Group: Members
Posts: 384
Joined: 4-December 07
From: Camarillo, CA
Member No.: 8,424
Region Association: Southern California



Attached ImageAttached ImageAttached Image[attachmentid=264
324]
ALL 914ers:

I've come up with a great way to repair the cracks in the dash cover yourself
with minimal tools and a little work:

1) Remove the dash cover from the car by loosening the nylon nuts holding it in place. This will leave the dash in place.

2) Buy 2 things:
-FLEXIBLE body filler made for repairing plastic bumpers (~~$20)
This is like Bondo, but formulated to remain flexible after setting.
-Eastwood # 12742Z Flexible Sealer and Sound Deadener from
Jegs as they are $5 cheaper than Eastwood.
http://www.jegs.com/i/Eastwood/352/12742Z/10002/-1

3) Remove foam back from the edges of cracks to create a good pocket to hold the putty. I used a Dremel tool, but it could also be done with an X-Acto knife.
(Harbor Freight has a "Dremel" tool for ~~ $9)

4) Mix the putty and fill the cracks leave enough sticking above the level of the dash cover to allow sanding flush.

5) Sand carefully with 50 or 60 grit until almost flush, then finish with 100 grit.

6) With the surface of the dash cover now smooth when sliding your hand up & down its length, spray the Eastwood sealer in long smooth passes over the part as a 12" - 18" distance. I found 18" very good for laying an even coat.
I found that the spary nozzle is NOT a paint type and afte a pass of spraying, excess sealer will build up on the nozzle and cause large drops on the sprayed finish. The solution was to wipe the nozzle clean after each pass.

7) After the plastic coat has dryed, it can be sanded to 50-60 grit sanding block to smooth out the layer.

8) The Eastwood can is good for 3 good coats, so you must plan on make your 3rd coat your last.

Attached are photos of the results: a smooth, nicely textured flexible plastic surface.

Enjoy,
Terry


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Andyrew
post Jun 22 2011, 01:31 PM
Post #2


Spooling.... Please wait
**********

Group: Members
Posts: 13,376
Joined: 20-January 03
From: Riverbank, Ca
Member No.: 172
Region Association: Northern California



Side note, HF's dremmel tool isnt worth $9.. Buy a real dremmel for $40 as its well worth the money in comparison.

Terry, this is a great writeup! do you have any in progress pics?

Im curious how long this coating will last in the sun before it starts looking dried out.

Thanks for the writeup!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
76-914
post Jun 22 2011, 02:57 PM
Post #3


Repeat Offender & Resident Subaru Antagonist
**********

Group: Members
Posts: 13,455
Joined: 23-January 09
From: Temecula, CA
Member No.: 9,964
Region Association: Southern California



Good job, Terry. Looks great. I hope it stands up and that you have discovered something that can benefit the majority of our members. Will you give us a 3,6 & 12 month updates? I hope, I hope! Btw, ignore the negative comments if they start to fly. I love thinking outside of the parallelogram. (IMG:style_emoticons/default/piratenanner.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Zundfolge
post Jun 22 2011, 03:17 PM
Post #4


Senior Member
***

Group: Members
Posts: 847
Joined: 12-August 07
From: Colorado Springs
Member No.: 7,994
Region Association: Rocky Mountains



That's all kinds of awesome!

ya know, if one had access to a good sewing machine and some leather I bet one could stop at step 5 and then sew a leather cover that you could stick down with spray adhesive and it would last even longer.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
campbellcj
post Jun 22 2011, 10:05 PM
Post #5


I can't Re Member
****

Group: Members
Posts: 4,536
Joined: 26-December 02
From: Agoura, CA
Member No.: 21
Region Association: Southern California



Terry, that's a great DIY solution. My dash is in fairly bad shape but for a race car a new dash or pro re-cover seems silly. Thanks for posting this!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Prospectfarms
post Jun 22 2011, 10:28 PM
Post #6


Member
**

Group: Members
Posts: 495
Joined: 7-March 11
From: Louisville, KY
Member No.: 12,801
Region Association: Upper MidWest



Thank you very much for sharing your good idea and photos. Every time I look at the cracks in my otherwise fine dash cover I think about some way to fill them. Apparently so did you.

Per exposure to sunlight: lots of folks put elastomeric undercoat on the outsides of things -- even cars -- so I'm thinking it contains a uv inhibitor. That would be pretty easy to figure out.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
stewteral
post Jun 22 2011, 11:42 PM
Post #7


Old Member
**

Group: Members
Posts: 384
Joined: 4-December 07
From: Camarillo, CA
Member No.: 8,424
Region Association: Southern California



QUOTE(76-914 @ Jun 22 2011, 01:57 PM) *

Good job, Terry. Looks great. I hope it stands up and that you have discovered something that can benefit the majority of our members. Will you give us a 3,6 & 12 month updates? I hope, I hope! Btw, ignore the negative comments if they start to fly. I love thinking outside of the parallelogram. (IMG:style_emoticons/default/piratenanner.gif)


Please don't hold your breath on updates as the bare chassis is still up on the rotisserie. It is likely to be a year before I'll be finished and driving it.

Terry
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
stewteral
post Jun 22 2011, 11:45 PM
Post #8


Old Member
**

Group: Members
Posts: 384
Joined: 4-December 07
From: Camarillo, CA
Member No.: 8,424
Region Association: Southern California



QUOTE(Zundfolge @ Jun 22 2011, 02:17 PM) *

That's all kinds of awesome!

ya know, if one had access to a good sewing machine and some leather I bet one could stop at step 5 and then sew a leather cover that you could stick down with spray adhesive and it would last even longer.


Originally, I was looking at gluing vinyl over the sanded putty, but since I'm NOT an upholstery guy, was concerned about the compound curves and getting it to fit right.

The plastic spray was the perfect solution.

Terry
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
stewteral
post Jun 22 2011, 11:48 PM
Post #9


Old Member
**

Group: Members
Posts: 384
Joined: 4-December 07
From: Camarillo, CA
Member No.: 8,424
Region Association: Southern California



QUOTE(campbellcj @ Jun 22 2011, 09:05 PM) *

Terry, that's a great DIY solution. My dash is in fairly bad shape but for a race car a new dash or pro re-cover seems silly. Thanks for posting this!


I agree! On my 914V8 track car, I shamelessly slapped a dash rug on top and forgot about the ugly dash underneath!

Terry
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Valy
post Jun 23 2011, 03:35 PM
Post #10


Senior Member
***

Group: Members
Posts: 1,671
Joined: 6-April 10
From: Sunnyvale, CA
Member No.: 11,573
Region Association: Northern California



nice work!
i did something similar last year (you can search it here or on the club)
i recomend to spray vinyl paint over to get glare it had in its glory time.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 28th March 2024 - 06:03 PM