Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 
 Reply to this topicStart new topic
> Rust Removal, In those sensitive areas
Loser_Cruiser
post Dec 30 2011, 10:20 PM
Post #1


Member
**

Group: Members
Posts: 407
Joined: 4-April 05
From: Bellingham, WA
Member No.: 3,873
Region Association: Pacific Northwest
What is the best method for rust removal on parts that have machined or bearing surfaces?

I have some spindles that have surface rust that I would like to remove but the machined and bearing surfaces are still nice and clean and would like to keep them that way.

Thanks!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ThePaintedMan
post Dec 30 2011, 10:25 PM
Post #2


Advanced Member
****

Group: Members
Posts: 3,886
Joined: 6-September 11
From: St. Petersburg, FL
Member No.: 13,527
Region Association: South East States
QUOTE(Loser_Cruiser @ Dec 30 2011, 11:20 PM) *

What is the best method for rust removal on parts that have machined or bearing surfaces?

I have some spindles that have surface rust that I would like to remove but the machined and bearing surfaces are still nice and clean and would like to keep them that way.

Thanks!


Brass brush? (IMG:style_emoticons/default/unsure.gif) Any kind of phosphoric acid product would work too, I think.

-George
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914werke
post Dec 30 2011, 10:58 PM
Post #3


"I got blisters on me fingers"
**********

Group: Members
Posts: 10,066
Joined: 22-March 03
From: USofA
Member No.: 453
Region Association: Pacific Northwest
Soda
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
wingnut86
post Dec 30 2011, 11:05 PM
Post #4


...boola la boo boola boo...
***

Group: Members
Posts: 1,053
Joined: 22-April 10
From: South Carolina
Member No.: 11,645
Region Association: South East States
No joke, the old guys would say poor coke or 7-up on it.

Same as the soda trick. Straight fountain soda works best. Used to clean floors in a sub shop in the early 70s with the soda...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cwpeden
post Dec 31 2011, 03:12 AM
Post #5


Great White North, huh?
***

Group: Members
Posts: 916
Joined: 20-August 06
From: Victoria BC
Member No.: 6,693
Region Association: Canada
I took the innner tube from a bike and used duct tape to hold it on the spindle. 3 layers of tape will stand up to most.

I left the tie rod end in.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brodie
post Dec 31 2011, 10:54 AM
Post #6


Newbie
*

Group: Members
Posts: 39
Joined: 28-October 09
From: Kansas
Member No.: 10,990
Region Association: None
Blast it with walnut shells or glass. Wrap the bearing surfaces with duct tape. The shells or glass won't hurt the bearing surfaces, but I'd wrap it anyways. That should work just fine.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cap'n Krusty
post Dec 31 2011, 11:13 AM
Post #7


Cap'n Krusty
**********

Group: Members
Posts: 10,794
Joined: 24-June 04
From: Santa Maria, CA
Member No.: 2,246
Region Association: Central California
We use a product called "Evaporust". Removes the rust, protects the surfaces chemically. Great stuff! Note: Takes the bluing off of gun parts.

The Cap'n
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rohar
post Dec 31 2011, 11:21 AM
Post #8


Senior Member
***

Group: Members
Posts: 924
Joined: 25-October 08
From: spokane
Member No.: 9,685
Region Association: None
I'm assuming this is a stub. If you don't have a blasting unit, grab some blasting media and an empty paint can. Use electrical tape to cover the machined surfaces that currently look good then put it in the paint can. Fill the can with media until the stub is covered and put the lid on. Then hang the paint can from a rafter or some other thing that will keep it suspended.

Then duck tape a palm sander without any sand paper to the bottom of the paint can and turn it on. Go away as the noise is annoying. Come back in 30 minutes to your shiny new stub.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brodie
post Dec 31 2011, 11:36 AM
Post #9


Newbie
*

Group: Members
Posts: 39
Joined: 28-October 09
From: Kansas
Member No.: 10,990
Region Association: None
Rohar,

That is absolutely crazy, but somehow genius at the same time! I'm probably not going to try it, but talk about thinking outside the box. (IMG:style_emoticons/default/aktion035.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rohar
post Dec 31 2011, 12:10 PM
Post #10


Senior Member
***

Group: Members
Posts: 924
Joined: 25-October 08
From: spokane
Member No.: 9,685
Region Association: None
Believe it or not, I've bolted a cheep orbital, permanently, to a paint can for just this use. If you fill it with small ball bearings it'll polish the hell out of cast aluminum too.

I've been thinking I should attach the whole mess to an old strut spring so i don't have to hang it anymore, but meh, I've got better things to do.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
infraredcalvin
post Dec 31 2011, 12:24 PM
Post #11


Distracted Member
***

Group: Members
Posts: 1,517
Joined: 25-August 08
From: Ladera Ranch, CA
Member No.: 9,463
Region Association: Southern California
Home made tumbler, GREAT IDEA! You could also look up tumbling media on a site like eastwood to get an idea of what can be used on what type of surfaces. Can be used to clean up nuts and bolts and othe corroded small parts.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rohar
post Dec 31 2011, 02:11 PM
Post #12


Senior Member
***

Group: Members
Posts: 924
Joined: 25-October 08
From: spokane
Member No.: 9,685
Region Association: None
I've got my eye out for a cheep poly cement mixer for similar reasons...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
dlestep
post Dec 31 2011, 02:29 PM
Post #13


I am smilin'...
***

Group: Members
Posts: 890
Joined: 15-January 08
From: Sunrise Florida
Member No.: 8,573
Region Association: South East States
For everyone...
Take a standard 55 gallon drum.
Cut retangular port, install piano hinge and latch on side.
Install 2 inch pipe through lid and bottom, centered.
Install standard shaft carrier with sleeve bearings, one on bottom and one on lid.
Terminate shaft-end by welding solid shaft with key.
Install 10" pulley on keyed shaft, using grub-screw locking ring.
Weld or bolt together base frame from two by two steel angle. Base footprint
design needs to be sturdy enough to support assembly and parts...(250lbs dynamic).
Locking sissor frame okay, if sufficient in design.
Install retangular motor mount on frame.
Install two stiff deflector rubber blades 180 degrees apart on the inside outer wall.
Install 120VAC Swamp Cooler electric motor onto mount with 1/4 solid rubber pad.
Install standard outdoor light switch housing to frame and wire motor and install
switch. I used a dimmer switch.
Insert abrasive media, about two to two and a half bags.

Now you can tumble suspension parts or anything that fits in the 55 gallon drum.
I made a smaller coffee can size container inside to tumble smaller parts at the same
time without have to look for them for an hour....
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 17th May 2024 - 03:55 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...