 Seized No one main bearing, But also found this |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jeffdon |
 Jul 14 2013, 12:12 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,094 Joined: 24-October 06 From: oakland, ca Member No.: 7,087 Region Association: None  |
The thrust bearing on the cam shaft lost one of its flanges? WTF? How does this happen? Anyone seen this? Maybe some extra metal from the failure got into my main bearing?
 |
   |
 
|
Posts in this topic
jeffdon Seized No one main bearing Jul 14 2013, 12:12 PM
OCD Performance
The thrust bearing on the cam shaft lost one of i... Jul 14 2013, 01:21 PM
jeffdon
The thrust bearing on the cam shaft lost one of ... Jul 14 2013, 02:09 PM OCD Performance In all my years of working on Type 2, 411, 412 and... Jul 14 2013, 05:44 PM Cap'n Krusty I'd sure take a careful look at the condition ... Jul 14 2013, 06:18 PM r_towle After seeing both, if this is the same motor with ... Jul 14 2013, 06:56 PM jeffdon
After seeing both, if this is the same motor with... Jul 14 2013, 07:17 PM Mark Henry
After seeing both, if this is the same motor wit... Jul 14 2013, 07:58 PM jeffdon
[quote name='jeffdon' post='1895163' date='Jul 14... Jul 14 2013, 08:05 PM OCD Performance
After seeing both, if this is the same motor wit... Jul 14 2013, 08:16 PM jeffdon
[quote name='jeffdon' post='1895163' date='Jul 14... Jul 14 2013, 08:22 PM OCD Performance Yup a whole new case. Much better than half a case... Jul 14 2013, 08:46 PM jeffdon
Yup a whole new case. Much better than half a cas... Jul 14 2013, 09:10 PM OCD Performance did the cam shaft come in contact with the block w... Jul 14 2013, 09:24 PM jeffdon
did the cam shaft come in contact with the block ... Jul 15 2013, 08:08 AM Cap'n Krusty Wait a minute. You snapped the cam because the oi... Jul 15 2013, 09:05 AM jeffdon
Wait a minute. You snapped the cam because the o... Jul 15 2013, 09:51 AM Mark Henry
Wait a minute. You snapped the cam because the o... Jul 15 2013, 11:10 AM jeffdon
Wait a minute. You snapped the cam because the ... Jul 15 2013, 11:38 AM Mark Henry
[quote name='Mark Henry' post='1895434' date='Jul... Jul 15 2013, 11:49 AM jeffdon
[quote name='jeffdon' post='1895445' date='Jul 15... Jul 15 2013, 11:56 AM Mark Henry
Cam bolt to pump drive was fine. I stand correc... Jul 15 2013, 01:09 PM jeffdon
[quote name='jeffdon' post='1895451' date='Jul 15... Jul 15 2013, 01:13 PM Mark Henry
[quote name='jeffdon' post='1895451' date='Jul 1... Jul 15 2013, 01:31 PM DBCooper You posted while I was typing... and answered my q... Jul 15 2013, 09:58 AM jeffdon More forensics. Oil pump cover, showing wear, an... Jul 15 2013, 10:24 AM Java2570 A lot of folks say to use the stock Type 1 steel c... Jul 15 2013, 12:43 PM jeffdon
A lot of folks say to use the stock Type 1 steel ... Jul 15 2013, 12:49 PM r_towle take a picture of the end of the camshaft...the bo... Jul 15 2013, 01:36 PM jeffdon
take a picture of the end of the camshaft...the b... Jul 15 2013, 01:48 PM worn
take a picture of the end of the camshaft...the ... Jul 16 2013, 02:27 PM 76-914
[quote name='r_towle' post='1895501' date='Jul 15... Jul 24 2013, 03:57 PM Cap'n Krusty
[quote name='jeffdon' post='1895508' date='Jul 15... Jul 24 2013, 05:06 PM r_towle
[quote name='jeffdon' post='1895508' date='Jul 1... Jul 25 2013, 07:14 PM zig-n-zag Gene Berg manufactures Cast Iron oil pump covers. Jul 15 2013, 02:27 PM jeffdon
Gene Berg manufactures Cast Iron oil pump covers.... Jul 15 2013, 02:29 PM Cap'n Krusty I guess I wasn't clear, coupled with misunders... Jul 16 2013, 02:36 PM Mark Henry
I guess I wasn't clear, coupled with misunder... Jul 16 2013, 02:54 PM jeffdon
I guess I wasn't clear, coupled with misunder... Jul 24 2013, 03:43 PM jeffdon
I guess I wasn't clear, coupled with misunder... Jul 24 2013, 03:43 PM McMark Your pump and your cam gear need modification/clea... Jul 16 2013, 03:12 PM r_towle
Your pump and your cam gear need modification/cle... Jul 16 2013, 03:29 PM Jake Raby Failed cam bearings in this manner are somewhat no... Jul 16 2013, 07:04 PM r_towle
Failed cam bearings in this manner are somewhat n... Jul 16 2013, 07:45 PM Jake Raby
Failed cam bearings in this manner are somewhat ... Jul 24 2013, 07:09 PM jeffdon
[quote name='r_towle' post='1896094' date='Jul 16... Jul 25 2013, 08:19 AM Java2570 When the first cam got damaged by the oil pump, di... Jul 16 2013, 08:10 PM jeffdon
When the first cam got damaged by the oil pump, d... Jul 25 2013, 09:19 AM jeffdon Well, I got offered a 1.7 case for 50 bucks. Got ... Jul 24 2013, 03:41 PM jeffdon Man, thats a bad one.
Well, its allegedly been ch... Jul 24 2013, 04:27 PM Jake Raby Any loss of thrust control can lead to this. The f... Jul 25 2013, 06:45 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th May 2024 - 03:00 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.