 Tranny mount question |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Amphicar770 |
 Apr 23 2014, 08:18 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,191 Joined: 20-April 10 From: PA, USA Member No.: 11,639 Region Association: MidAtlantic Region 
 |
Hi All,
Just did the engine mounts and am in the process of doing the transmission mounts. I seem to have additional parts on my mount that I do not see in the standard diagrams. I also notice that the long bolts on mine were inserted from the top rather than up from the bottom as shown in the diagram. The small serated washer was at the top of the bolt head when it was inserted opposite from shown in photo. The other mystery washer sitting next to the assembly is rather thick and is cupped as if it might somehow sit over the mount. Should it even be there and, if so, where? Any ideas or insight? Thanks.  |
   |
 
|
  |
Replies
| bulitt |
Apr 24 2014, 06:10 AM
Post
#2
|
|
Achtzylinder Group: Members Posts: 4,188 Joined: 2-October 11 Member No.: 13,632 Region Association: South East States |
|
|
|
|
| rgalla9146 |
Apr 24 2014, 07:52 AM
Post
#3
|
|
Advanced Member Group: Members Posts: 4,554 Joined: 23-November 05 From: Paramus NJ Member No.: 5,176 Region Association: None
|
QUOTE(bulitt @ Apr 24 2014, 08:10 AM)  As delivered from the factory the long bolts were inserted from the top. That original arrangement makes engine/trans removal/ install a real PITA. By now it's unusual to find them still that way. Those cupped washers ?.....out. |
|
|
|
| Cap'n Krusty |
Apr 24 2014, 08:40 AM
Post
#4
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
QUOTE(rgalla9146 @ Apr 24 2014, 06:52 AM) QUOTE(bulitt @ Apr 24 2014, 08:10 AM) As delivered from the factory the long bolts were inserted from the top. That original arrangement makes engine/trans removal/ install a real PITA. By now it's unusual to find them still that way. Those cupped washers ?.....out. Interesting you say they're installed from the top when the factory parts diagram accompanying your comment clearly shows them installed from the bottom. The Cap'n |
|
|
|
Posts in this topic
Amphicar770 Tranny mount question Apr 23 2014, 08:18 PM
bdstone914 Mystery washer not needed.
Bolt normally goes in f... Apr 23 2014, 09:43 PM Jeffs9146 never mind Apr 23 2014, 11:49 PM CptTripps Extra parts: You're good at improving someone... Apr 24 2014, 05:42 AM
Qarl The schnoor washer (serrated tiny washer) and the ... Apr 24 2014, 07:53 AM SLITS Up or down ... does it really make a difference? ... Apr 24 2014, 08:42 AM
type47
I also notice that the long bolts on mine were... Apr 24 2014, 09:24 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th May 2024 - 10:04 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.