 New rear PMB alloy calipers. Now no break pressure |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Downerman |
 Sep 17 2014, 04:57 PM
Post
#1
|
|
Member  Group: Members Posts: 168 Joined: 23-April 09 From: Monterey County, California Member No.: 10,296 Region Association: None  |
OK, OBVIOUSLY no negative to the calipers. Here's the deal..... removed the 911 rear calipers (well for that matter the entire swing arms) but I just let the brake fluid lines hang and drain into jars. Finally got my swing arms mods done and now putting on the new calipers. Filled the brake resevoir up and had all 4 wheels off the car. Used my handy dandy brake sucker pump and had fluid running to all four bleeders on the rear (2 each for a caliper) and then did the fronts. Had to refill a couple of times because I was pulling some darker fluid until it was clear. Went into the cab and hit the breaks. Nothing.... I mean NADA. Pumped like a 100 times to no avail.
RE-DID the entire process again. NADA and I mean nothing. So, I'm wondering if my master has gone south in this time line?? and why?? Seems the only logical answer at this point. Anyone have any ideas? Dave |
   |
 
|
Posts in this topic
Downerman New rear PMB alloy calipers. Now no break pressure Sep 17 2014, 04:57 PM
wndsrfr
OK, OBVIOUSLY no negative to the calipers. Here... Sep 17 2014, 05:06 PM Mblizzard If you go to the old open the bleeder and pump the... Sep 17 2014, 05:08 PM
Downerman Yes, maybe 3-4 weeks.
Dave
If you go to the o... Sep 17 2014, 05:23 PM Downerman Found this.... same issue as mine using a "Su... Sep 17 2014, 05:31 PM 76-914 Yep, bench bled time. Sep 17 2014, 05:31 PM Downerman Ok, bench bleed time. I've read some posts th... Sep 17 2014, 05:35 PM rgalla9146
Ok, bench bleed time. I've read some posts t... Sep 17 2014, 05:52 PM Jeffs9146 Just crack the lines at the MC. Make sure there is... Sep 17 2014, 05:43 PM Elliot Cannon If the system was dry for 3 to 4 weeks, the seals ... Sep 17 2014, 06:19 PM Tbrown4x4 If the M/C is old, sometimes rust and dirt settle ... Sep 17 2014, 07:36 PM Downerman Thanks everyone for the info. Yeah I started with... Sep 17 2014, 07:46 PM Jeffs9146 By loosening the outlines on the MC and letting it... Sep 17 2014, 07:59 PM Downerman Ok Jeff, I will try this in the morning. Thanks a... Sep 17 2014, 08:31 PM Downerman For those who care to know..... I bled the M/C to ... Sep 22 2014, 10:38 AM Dave_Darling Wait, what??? The calipers were not in the regula... Sep 22 2014, 04:22 PM Downerman I have a great pedal right now. Eric didn't t... Sep 22 2014, 06:21 PM rgalla9146 ......... you would have had your solution much so... Sep 22 2014, 06:43 PM Downerman You are correct sir!!! As I said ab... Sep 22 2014, 06:55 PM ClayPerrine I had the same issue on my old Jeep truck. I had t... Sep 23 2014, 06:07 AM 9146986 Pressure bleeding is the only way to go.
Here... Sep 23 2014, 07:41 AM kkid
Pressure bleeding is the only way to go.
Here... Sep 23 2014, 10:44 AM Downerman Nice..... so what do you think the difference is ... Sep 23 2014, 11:12 AM Tbrown4x4 So....Any luck?
I'm also a fan of pressure bl... Sep 28 2014, 10:54 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 5th May 2024 - 05:33 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.