|
|

|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| raynekat |
Feb 11 2015, 07:22 PM
Post
#1
|
|
Advanced Member ![]() ![]() ![]() ![]() Group: Members Posts: 2,171 Joined: 30-December 14 From: Coeur d'Alene, Idaho Member No.: 18,263 Region Association: Pacific Northwest
|
Bought a 71 1.7 liter today.
Car is in relatively good shape as far as I can tell. Likely some hell hole and rear portion of the back trunk rust repair needed, but appears to be minor. Time will tell. My current plans are to get the fuel system and FI sorted out (me). It cranks over, but doesn't start. Then go through the brakes from stem to stern (PMB). After that....drive it. The original color is light ivory, but has had a repaint in pearl white years ago. Will get the body work done and do a proper respray. I've already got a set of 15x6.5" Minilites to install. The suspension will get a good going over....likely Elephant Racing setup. Re-do the interior with a more supportive driver's seat. Refreshed gauges (Hollywood Speedo) in 356 fashion. Double wrapped RS steering wheel. GT lightwt door panels. Eventually, a bigger four will power the car. Would like to keep it all 4 cylinder for the time being. I've already got a 911 sitting in the garage that tics all the 911 boxes off. I'll keep a log of the progress here with pics. This is a big, big project.....no doubt. |
raynekat Just arrived in the garage: 1971 914-4 1.7 Feb 11 2015, 07:22 PM
cary Friday 5/5/17 Short Day
Trimming up and in the ri... May 5 2017, 09:22 PM
raynekat New shoes for the car.
A set of ultra-lite Mahle g... May 8 2017, 11:31 PM
raynekat Also just received my gauges back from North Holly... May 8 2017, 11:42 PM
Cairo94507 I love your gas burners.
Your instruments look b... May 9 2017, 06:41 AM
raynekat Rebuilt the steering column today.
Repainted the ... May 12 2017, 07:54 PM
raynekat RE: Just arrived in the garage: 1971 914-4 1.7 May 12 2017, 07:55 PM
cary Friday 5/12/17
The right seat belt retractor pock... May 13 2017, 06:36 AM
cary Next ......................... on to the Hell Hole... May 13 2017, 06:49 AM
cary Saturday 5/12/17
Back to cutting out the hell hol... May 14 2017, 10:22 AM
raynekat Obtaining/reconditioning parts for the side shift ... May 15 2017, 01:25 AM
raynekat Close up of the new shift rod bushings.
Your frien... May 15 2017, 01:30 AM
raynekat Pulled the shifter apart to clean it, paint it, in... May 15 2017, 01:34 AM
raynekat The rear console just required some light cleaning... May 15 2017, 01:35 AM
raynekat Now for a break in my restoration activities.....
... May 18 2017, 03:58 PM
cary Congrats from Julie, I and Super In Law.
They... May 18 2017, 05:06 PM
altitude411 Wow, how blessed, beautiful little angels. Congrat... May 18 2017, 05:11 PM
raynekat Future Porsche pilots /mechanics. May 18 2017, 05:21 PM
cary Friday 5/18/17
Start the day with pulling the fro... May 18 2017, 10:45 PM
cary While I'm welding, Super In Law started the wo... May 18 2017, 11:09 PM
cary Friday 5/19/17
Short day on Doug's car. Rebuil... May 20 2017, 10:14 AM
raynekat
I'll pull one of Mark's sway bar bushing... May 20 2017, 04:10 PM
cary Onto the inside. Looks like the hillbillies used a... May 20 2017, 10:31 AM
cary Made a house call and picked up Doug's front s... May 26 2017, 08:12 AM
cary Here's a couple better shots of what I was try... May 26 2017, 10:35 PM
cary After lunch it was time to start welding in the he... May 26 2017, 10:47 PM
cary Wheelhouse welded in and covered with cold galvani... May 28 2017, 09:34 AM
mb911 Just did the exact same repair the same way. Great... May 28 2017, 12:35 PM
cary Took most of Sunday off to try and beat this virus... May 29 2017, 09:23 PM
cary Back from WCR and back to work.
Time to install th... Jun 10 2017, 12:10 AM
cary Started the day with pulling out the plasma cutter... Jun 10 2017, 11:23 PM
cary Next Saturday Project :
Getting the parts car pre... Jun 11 2017, 09:16 AM
cary Time to dive into the deep end .................
W... Jun 11 2017, 09:31 AM
cary So lets go burn some metal ...............
Time fo... Jun 11 2017, 09:46 AM
cary Back to trimming off/out the portion of the cowl I... Jun 11 2017, 10:00 AM
raynekat Finished up the engine side of the front 914-6 eng... Jun 15 2017, 09:35 AM
raynekat Quick clean up of the original jack.
Wanted a bit ... Jun 15 2017, 09:40 AM
raynekat Just received these bad boys in the mail from Elep... Jun 15 2017, 09:49 AM
cary Thursday 6.15.17
Welded in Super In Laws tuned up... Jun 16 2017, 08:56 AM
mb911 Looking good.. Tackling many of the same things on... Jun 16 2017, 10:43 AM
cary :sawzall:
Out came the cowl/windshield frame.
... Jun 16 2017, 10:51 PM
cary Trimming down the cowl removed from the parts car.... Jun 18 2017, 05:49 AM
cary Thursday 6/22/17
First task before it gets too ho... Jun 22 2017, 09:16 PM
cary As I wait for a couple inquiries Matt sent out on ... Jun 24 2017, 07:16 AM
cary Next project.
I'll have Super In Law build a ... Jun 24 2017, 07:26 AM
cary Today was the big day .................
Decided it... Jul 1 2017, 10:47 PM
cary Taking a break from the cowl/fender. Applied cold ... Jul 7 2017, 10:08 PM
Cairo94507 Terrific work. :beer2: Jul 8 2017, 07:10 AM
cary Thank You .................
Today should be a big... Jul 8 2017, 08:52 AM
cary Saturdays work ................ didn't quite g... Jul 11 2017, 08:19 AM
raynekat That Eastwood internal frame coating system looks ... Jul 11 2017, 12:11 PM
Fatboy007 Very nice...looks clean. :D Jul 11 2017, 01:50 PM
cary Seems like I've been gone forever ............... Jul 21 2017, 10:17 PM
cary Now the fun stuff, new metal.
Prepped the flanges... Jul 21 2017, 10:39 PM
raynekat Just received back some parts from Burnham Perform... Jul 22 2017, 03:44 PM
raynekat Secondly, Burnham Performance restored and recurve... Jul 22 2017, 03:46 PM
raynekat One of the fun parts about doing a 914-6 conversio... Jul 23 2017, 08:30 PM
raynekat All the various switches and relays attached.
Nice... Jul 23 2017, 08:36 PM
raynekat Every wire connection identified, traced, confirme... Jul 23 2017, 08:37 PM
cary It's time for the throw down to begin ......... Aug 1 2017, 07:52 AM
raynekat
It's time for the throw down to begin ........ Aug 1 2017, 09:50 AM
tygaboy Beautiful work... I could watch it all day. Aug 1 2017, 07:56 AM
raynekat Latest Porsche porn to show up at my doorstep.
MF... Aug 1 2017, 12:20 PM
914_teener
Latest Porsche porn to show up at my doorstep.
M... Aug 10 2017, 09:31 PM
raynekat In addition, Mark supplies a nice flow chart for t... Aug 1 2017, 12:21 PM
raynekat Today I delivered a mountain of engine parts to Ro... Aug 2 2017, 05:32 PM
cary Jeff (Rothsport) is adding pressure to the Throwdo... Aug 3 2017, 06:57 AM
cary Throwdown Day #1.
While I'm working on the fl... Aug 3 2017, 07:27 AM
cary Throwdown Day #2.
Patched the cut out in the corn... Aug 3 2017, 07:29 AM
cary Day #3 ....................
All pieces installed ... Aug 3 2017, 07:39 PM
raynekat Everything is looking great.
After such a hot day ... Aug 3 2017, 10:01 PM
cary Day #4 on the ThrowDown.
Worked on the reworking o... Aug 5 2017, 10:13 AM
cary Now where was I. Here's Rick's measurement... Aug 5 2017, 10:59 PM
cary Started Day #5 locating my second left seat frame ... Aug 6 2017, 12:45 AM
cary As I'm working on the chassis Super In Law is ... Aug 6 2017, 08:44 AM
cary Fell asleep last night while writing the post ....... Aug 6 2017, 09:01 AM
raynekat When these stiffening plates are welded in....is i... Aug 7 2017, 05:17 PM
cary Calls out seam welded too. Edges have been prepped... Aug 7 2017, 07:43 PM
raynekat
Calls out seam welded too. Edges have been preppe... Aug 7 2017, 08:41 PM
cary You're right, I got the Miller cranked up even... Aug 7 2017, 10:26 PM
cary Here's a couple shots of my door gap measureme... Aug 8 2017, 12:20 AM
cary Day #7. Worked a little over a half day. Finished ... Aug 9 2017, 07:36 AM
cary Day #8. Only put in a couple hours welding yesterd... Aug 10 2017, 07:58 AM
cary The rosette welding has been completed on both sid... Aug 11 2017, 08:26 AM
raynekat While Cary's off hiking in the woods collectin... Aug 12 2017, 09:33 AM
raynekat I've always got on hand the correct wire conne... Aug 12 2017, 09:37 AM
mepstein
I've always got on hand the correct wire conn... Aug 12 2017, 10:05 AM
raynekat Working or mocking up the new LED headlight bulbs ... Aug 12 2017, 03:08 PM
raynekat The H4 assemblies from 914 Rubber are quite nice.
... Aug 12 2017, 03:10 PM
raynekat Wet sanded and painted my "white" headli... Aug 12 2017, 03:14 PM
cary Back at it. Seam welded in the left 3 fender porti... Aug 22 2017, 07:38 AM
mb911
Back at it. Seam welded in the left 3 fender port... Aug 22 2017, 08:06 AM
cary It's Tuesday and back at the welder.
First p... Aug 23 2017, 08:03 AM
raynekat Fiddling around with my side shift rear rod today.... Aug 31 2017, 05:18 PM
raynekat Then I aligned the hole for the conical screw; I h... Aug 31 2017, 05:22 PM
raynekat Quick pic sent to me today of the 2.7RS short bloc... Aug 31 2017, 06:39 PM
raynekat My new seatbelts arrived from Seatbelt Planet toda... Sep 1 2017, 09:29 PM
raynekat Also today in the mail arrived my "custom... Sep 1 2017, 09:34 PM
raynekat Last on the agenda for today was finishing up the ... Sep 1 2017, 09:40 PM
raynekat Worked on getting the new gauges all hooked up int... Sep 2 2017, 08:35 PM
raynekat Refurbished the 914-6 engine relay panel I had sou... Sep 2 2017, 08:48 PM![]() ![]() |
|
Lo-Fi Version | Time is now: 4th February 2026 - 01:31 AM |
| All rights reserved 914World.com © since 2002 |
|
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |