 My GT bumper |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Harpo |
 Jun 13 2015, 03:05 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,304 Joined: 21-August 11 From: Motor City aka Detroit Member No.: 13,469 Region Association: None  |
After seeing McMark GT bumper I decided I needed one of those but was too cheap to buy one from McMark so I made my own.
Here is McMark's bumper with some elaborate cutting  Here is Silverson's bumper a little simpler cutting involved so I took this route  |
   |
 
|
| Harpo |
Jun 13 2015, 03:08 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,304 Joined: 21-August 11 From: Motor City aka Detroit Member No.: 13,469 Region Association: None |
Here is mine
  |
|
|
|
| lonewolfe |
Jun 13 2015, 07:10 PM
Post
#3
|
|
Senior Member Group: Members Posts: 819 Joined: 12-September 11 From: Oakland, CA Member No.: 13,549 Region Association: Northern California |
Nice job! How long did that take you to complete?
|
|
|
|
| Harpo |
Jun 14 2015, 07:01 AM
Post
#4
|
|
Senior Member Group: Members Posts: 1,304 Joined: 21-August 11 From: Motor City aka Detroit Member No.: 13,469 Region Association: None |
Thank you
I have about 8 hrs in to this at this point. My welding skills are not so good. An accomplished welder with a metal band saw could do this much faster. |
|
|
|
| keely444 |
Jun 14 2015, 07:03 AM
Post
#5
|
|
Member Group: Members Posts: 103 Joined: 4-May 15 From: santa cruz Member No.: 18,702 Region Association: None |
Very trick, I want to do the same on my car. I wish I had your skills.
|
|
|
|
| mepstein |
Jun 14 2015, 09:00 AM
Post
#6
|
|
914-6 GT in waiting Group: Members Posts: 19,271 Joined: 19-September 09 From: Landenberg, PA/Wilmington, DE Member No.: 10,825 Region Association: MidAtlantic Region 
|
Scotty B represents on the east coast
Attached image(s)   
|
|
|
|
| Harpo |
Jun 14 2015, 01:36 PM
Post
#7
|
|
Senior Member Group: Members Posts: 1,304 Joined: 21-August 11 From: Motor City aka Detroit Member No.: 13,469 Region Association: None |
Way nicer than mine, but then again Scotty B welding skills are vastly superior to my feeble attempt.
|
|
|
|
| Cairo94507 |
Jun 14 2015, 01:38 PM
Post
#8
|
|
Michael Group: Members Posts: 9,752 Joined: 1-November 08 From: Auburn, CA Member No.: 9,712 Region Association: Northern California
|
That looks slightly familiar (IMG:style_emoticons/default/sunglasses.gif) Here it is with the valance done to match.
 |
|
|
|
| racerbvd |
Jun 14 2015, 06:27 PM
Post
#9
|
|
Advanced Member Group: Members Posts: 2,368 Joined: 3-February 03 From: Sunny FL. Member No.: 226 Region Association: None |
|
|
|
|
| EdwardBlume |
Jun 14 2015, 10:57 PM
Post
#10
|
|
914 Wizard Group: Members Posts: 12,338 Joined: 2-January 03 From: SLO Member No.: 81 Region Association: Central California
|
Show off! Nice work.
|
|
|
|
| Mark Henry |
Jan 21 2017, 01:02 PM
Post
#11
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
The big difference I see is the radius
so 19.5" X 1.5" with a 3/4" radius? This is for the bumper group buy, so I want to get it right. (IMG:style_emoticons/default/unsure.gif) |
|
|
|
| Mark Henry |
Jan 21 2017, 01:06 PM
Post
#12
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
Dang wrong thread (IMG:style_emoticons/default/rolleyes.gif)
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 14th May 2024 - 09:36 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.